similar to: Dumb TDM400P question

Hi, I'm no phone guy but I've been having quite a bit of fun messing with Asterisk. I just unwrapped my new Wildcard TDM400P (TDM40B) which is the new 4 port FXS PCI card. It has 4 RJ45 connectors and I'd like to hookup 4 regular phones which are RJ11. If I crip RJ45 connectors to the phone cords do I simple use the center two pins (pins 4 and 5)? Thanks, Randy Smith Tiger

Hi folks, Any Brits on the list got experience of hooking devices with standard BT plugs to the TDM400P? The TDM400P has the RJ11/RJ45 socket but I'm not sure if a standard adapter will do the trick or if we need to consider ring capacitors etc. Any links to buy the stuff would also be appreciated. Cheers, Simon -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm a complete Asterisk novice and have an installation based on the Asterisk@HomeCD. I've installed my TDM400P with 2 x FXO & 2 x FXS, but every time I try to dial out, I get a message "No circuits available". Can someone confirm the pinouts for connecting the FXO's to a UK BT Line - I have RJ11 connectors on the back of my TDM400P card, so ideally I'd like to

I just received a Wildcard TDM400P by FedEx yesterday. I noticed that the FXO/FXS modules use connectors similar to Ethernet. Now, i want to connect the TDM400P to the PSTN connector in the wall, and also to a regular analog phone. Both the PSTN conn and the phone use smaller connectors, typical for analog phones. I searched the "official" docs and the Wiki, there's good

Any hardware that can do 25-50-100 fxs ports trunked to sip ? Example one end a cat5 other end 50 RJ11's jacks.. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20090406/9514bc47/attachment.htm

Here is my system: POWER SUPPLY 450W ALLIED ATX450P4 R(41) MB NFORCE2 A7N8X DELUXE ASUS RTL(Standard) CPU AMD|2500/333 ATHLON XP BARTON R(Standard) DDRAM 256M|DDR333 PC-2700 -K %(Standard) HD 40GB|WD 7200RPM 8MB WD400JB%(70) VGA ASUS|V8170MAGICII/T 64M MX440SE(58) CD ROM 56X|AOPEN CD-956 RTL(22) Besides the above parts, i have 2 X100P FXO PCI cards, and 1 TDM40B I bought 2 phones from radio

Hi, this is probably a stupid question but can someone point me to where I can find the pinouts for the connector at the back of the TDM2400P card from Digium. I am assuming this is some kind of telecomms standard but I need to connect to 8 existing analogue lines and therefor need to wire this connector to a patch panel or R11 jacks. Also most of the docs do not mention this card - am I

Ok, I've pretty much decided to try the Adit route. Somebody who has experience with these tell me if I'm missing something. I have 15 incoming PSTN lines. T1 is not an option at current location. I want to put in an Adit 600 with 2 8-port FXO boards. The adit will then connect to * via a digium t1 board. I configure zaptel.conf for the T1. What other parts would be needed? How do

The HP DL380 G5 (like many rack servers) has no AMP Mate-n-Lok connector available to attach to a card that needs more power than the PCI bus can provide, like the TDM400P when FXS modules are used. HP has confirmed that there is no part they sell to give you such a connector, and Digium says their business edition folks got it to work, but only by doing nasty warranty-voiding things to the

<div><BR>Hello,</div> <div>&nbsp;I bought a TDM400P, and intended to use it with my analog phone, which is RJ11 ofcourse. So, the question now, how do I plug in my RJ11 phone to the TDM400P card, which has an RJ45 interface? Also, since it's an 11B card, I also intend to bring in an analog line into the RJ45, so i am still left with the same question....how do I go

I am hoping to replace my Nortel 8x24 switch with Asterisk. Right now my cabling comes from my outside phone box into my office and into a punchdown block and leaves the punchdown block as an amphenol connector which currently plugs into the Nortel swicth. A second amphenol connector them plugs into the switch and extends to another punchdown block that I believe carries the lines throughout the

If you have an FXS port and would like to attach a PSTN analog line to it this device would do the job by converting the FXS port to FXO. It's a small external device. Works well with VOIP FXS and other FXS interfaces. Interface: 2 RJ11 Jacks (one for the FXS port and one for the PSTN outlet.) Cost: $35.00 with USPS regular mail included. Power: 9 to 20V dc power supply (Not

We currently have a 15-phone system using Asterisk, a combination of analog phones/Grandstream HandyTone-286 and Grandstream BT101s, and 4 X100Ps connected to analog lines. The system works well except for the occasional echo problem. I have all the echo parameters configured, removed all the extra incoming analog lines except to the PBX, etc. following all the advice on the wiki and on the

Does the voicetronix card work with Asterisk? -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of woody+asterisk@solutionsfirst.com.au Sent: Monday, February 02, 2004 11:06 PM To: asterisk-users@lists.digium.com Subject: RE: [Asterisk-Users] Pictures of new multiport FXO/FXS from digum > -----Original Message-----

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

I need to ask, to refresh, is the aux power connector on the TDM400P card *only* to power the ringer on any analog phones/devices on the system? Can I still use this board, to "terminate" POTS lines and use all SIP Phones? Due to circumstances, I end up with a 1u server that has no aux power connectors available. I "have to" use this server, so am considering abandoning

Hi Asterisk Community, I have a development with a TDM11B in it. I am trying to connect this to a exchange line as well as a UK telephone and are looking for some pinout information for the FXS port. Is it the centre 2 pins that at the tip and ring. I have been digging around the Digium site but cannot seem to pick up this info. Any help appreciated. Thanks -- Gary

Hi, I'm trying to use a Detewe TA 33-clip but there is no rj11 connector on it...only a TAE connector. I'd like to create an adapter so I need to know which TAE pins to connect to RJ 11 pins. Is there anybody who knows where I can find a schema of that adapter? Single connector pinout may help too. TIA Giorgio Incantalupo

Ok... I am not a telephone guy... I was born after rotary phones, so forgive my ignorance in this matter. I am trying to get a really old rotary phone up and running with an ATA. Why? Who knows... just thought it would be cool. The problem is that it does not have an RJ11 connector, instead it has three wires (green,yellow,red). Does anyone know what that type of connector is called? Or

Has anyone come up with a way to get power to a TDM400P card installed in a Dell PowerEdge 1750? Thanks, Adam The contents of this email message and any attachments are confidential and are intended solely for addressee. The information may also be legally privileged. This transmission is sent in trust, for the sole purpose of delivery to the intended recipient. If you have received this