similar to: Problems with Quadbri card

Hi, I have an asterisk box with a QuadBRI. I am close to make it work like I want: Incoming calls to SIP are OK, outgoing calls are quiet working thanks to Michael Sandee advices. My real problem is that my * box is freezing very often when I probe qozap (bri-stuff 0.0.2). I have tried two distribs (Debian Kernel 2.6, Mandrake 9.1 Kernel 2.4) and it always work for a few minutes and freezes. At

Hi there, I am attempting to set up a simple BRI and SIP based platform using * with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and zapata.conf files. For the inital test I'm simply trying to connect to the * demo menu. The drivers compile (with a few warning that I believe aren't important - see attachments). chan_zap comiles with the warning: chan_zap.c:

Morning Asterikians, I've just got my nice shiny quadBRI card, and it seems to be working very well - except for one little issue - CallerID. The card is currently connected to an ISDN2e line in P2P mode, and an S0 adapter on our existing alcatel PBX. The S0 connection recieves callerID and displays it correctly - the 2e line doesn't, and BT have said that CLID was enabled on the

Hi All ... I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v which has a Junghanns QuadBri card in it (lspci reports Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)) I have a regular KPN ISDN2 Line connected which works fine with the the zapata.conf below. However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group), which works fine for incoming calls,

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Hi, I have Installed * on a DL380 with a Junghanns 4BRI card and 0.0.2 driver. I have 3 BRI lines connected to SPAN(TE) 1,2,3 and 2 Cisco 7960 with SIP image. I am connected to french PSTN (France Telecom) whith Euroisdn signaling. I manage to call SIP to SIP, PSTN to SIP but not SIP to PSTN. Any idea? Thanks Gwenn Gael Marronnier Here is what I get and my configuration...

Hi, I'll soon replace a Junghanns OctoBRI with a Junghanns QuadBRI. As both use wcb4xxp driver (dahdi 2.3.0, libpri 1.4.10.2 and asterisk 1.6.1), I'm planning to proceed this way : 1. Edit 2 versions of files /etc/dahdi/system.conf and /etc/asterisk/dahdi-channels.conf (one for each card). 2. Link current system.conf and dahdi-channels.conf to QuadBRI files. 3. Power PC off 4. Swap cards

Good afternoon, I have to develop an Asterisk system in Spain that can support up to 8 simultaneos ISDN calls (4 BRI), initially only 6 simultaneos calls. I have been looking into VOIP-INFO and I found that the Junghanns card QuadBRI is a very good option. But when I look for a server to develop the system, the information is a bit more confuse. Any one have experience with this card? Which

Hello, I am trying to install the drivers for the Junghanns quadBRI card, but am having a problem. I have essentially followed the procedure from http://www.voip-manager.net/installation-linux-asterisk.php. At the stage to install the ISDN card I have completed the following: 1) downloaded the bristuff-0.2.0-RC8q.tar.gz to /usr/src 2) unpacked it in /usr/src - tar xvzf bristuff-0.2.0-RC8q.tar.gz

Hello, I cannot make any call with my new quadBRI card from Junghanns.net in my asterisk box. My asterisk box is built on Fedora Core 3 linux system. After compiling drivers from junghanns.net the card driver was loaded correctly with - modprobe zaptel - insmod qozap.ko ( as FC3 is running a 2.6 linux kernel) - ztcfg -vvv ( shows 12 channels correctly configured and the 4 leds on the card were

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

Hi, we are using asterisk with Junghanns QuadBri and some sip phones. 2 channels are configured in NT mode (ISDN PBX connected, internal ) and 2 channels are connected to the public ISDN network (bri-cpe). We use Bristuff 0.2.0 RC8C from Junghanns. When a call comes in from the public phone for a specific extension (Hotline Number), we initiate a parallelcall to some SIP phones and also to our

Who is selling the quadBRI cards, which is everybody talking about? And how much does is costs? I'm looked on the site of junghanns.net, but there is no selling information. A seller in germany is favored.

Hello, Is anybody there using quadBRI form Junghanns.net with Asterisk ? I would like to order that card but first would like to hear some opinions. Thank you in advance Bartosz

Hi, I'm using a revision 6822-enabled Dahdi-Tools (see https://issues.asterisk.org/view.php?id=13897) with a Junghanns QuadBRI. 1. Do I still need qozap driver ? If positive, how is it recommended to get it ? 2. Which line should be included in /etc/dahdi/modules to have the appropriate driver loaded ? 3. The process I'm planning to use is : A- Hand edit /etc/dadhi/modules,

Hey, If anyone supplies or knows where I can get either an Eicon Diva V-4BRI or a Junghanns QuadBRI card in Australia, please could you contact me offlist? Also, if anyone has any second-hand ones they need to get rid of, I'd be interested in making an offer! I've been checking eBay, but there don't seem to be any of these available at the moment. Thanks, Avi -- National Manager -

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o