similar to: CallCenter setup

Hi * :-) I found in the online WiKi docs some information on how to integrate Asterisk with "old PBX"... http://www.voip-info.org/wiki-Asterisk+legacy+integration ...but I couldn't find anything on integration with a Siemens HiCom 150E. Later on we'll migrate to a HiPath 3750 so information covering this model would be nice too... Do you know if any of the PBX listed

Hello all, I am trying to connect asterisk to a Siemens Hipath 3750 PBX system. I have a physical connection issue. I know that I should use a crossover RJ48 cable to link the two systems. The problem however is that the physical interface of the Siemens system is very unfamiliar. From my digging around, I think that this is an S2M interface. http://www.mail-archive.com/asterisk-users at

hi all, we do have some troubles with zaptel timing source - we have a setup with 3 telco PRI lines, connected to asterisk digium card 0 - asterisk does some handling - calls are leaving on digium card 1 - going to a siemens hipath - there is some call handling - some of the calls then are going from the hipath over a qsig line to a bosch integral PBX - handling the rest of the calls. To be able

I am connecting to a siemens hipath 4000 with dahdi 2.1.0.4 and asterisk 1.4.23 using a Te210P card. the phone guy is saying that the lines are reporting always BUSY. however on my end the status shows OK. Anyone seen this? Is there something different about connecting PRI to siemens hipath? system.conf shows: loadzone=us defaultzone=us span=1,1,6,esf,b8zs bchan=1-5 dchan=24

Hi Stephen, You said that PRI works great. We are using HiPath 3550 and Siemens digital phone which using *11, *97 etc for function keys. However Asterisk uses the the * key plus one or two digits for function keys as well(it is common key combination for functions). So is it any way to disable *11, *97 keys in HiPath system and pass this keys to Asterisk? Thanks and regards, Isaac >Hi

Hello! Is it possible to connect Siemens HiPath 4000 to Asterisk? What equipment required on Siemens side? I mean IP not E1. Sorry for asking here. Siemens-related websites use "salesperson language". There is no technical information.

Hi Group, I am currently facing a dead end and any help will be much appreciated. I have an a104d installed in an asterisk box, two of which is configured on ISDN pri. One is facing pstn and the other one is facing a hipath 300e Siemens. I am getting one way audio when a local on the hipath tries to make a pstn call but no issue on incoming calls from pstn going to the hipath locals. local

Hi, I am currently using asterisk to record all incoming calls. My setup is as follows, the asterisk server has a two TE120P cards one of which sends/receives calls from the carrier and the other is connected to a Siemens HiPath 3000. All calls that come into asterisk use MixMonitor to record calls and this works fine, but if a call gets transferred the transfer information is not sent back to my

Hello all. I have installed and functioning asterisk-1.2.9.1 where I effected one upgrade in asterisk-1.0.9, is interconnected with a PABX Siemens HiPath 4000 in ISDN PRI with protocol QSIG, the one that is happening he is that the calls originated for PABX Siemens and destined to SIP phones asterisk are being without audio, nor Ring, is dumb. They could help in this case me? Best Regards Josu?

Hi all, I'm trying to setup Asterisk trunk to Siemens HiPath 4000 V2.01 What would be the best way to do so? I am a bit confused because as far as I've understand this PBX doesn't support H323, but I saw somewhere someone who created a cornet trunk and it worked using H323. So if anyone knows what I need to configure I would appreciate it. I've read some information

Hello all. I have installed and functioning asterisk-1.2.9.1 where I effected one upgrade in asterisk-1.0.9, is interconnected with a PABX Siemens HiPath 4000 in ISDN PRI with protocol QSIG, the one that is happening he is that the calls originated for PABX Siemens and destined to SIP phones asterisk are being without audio, nor Ring, is dumb. They could help in this case me? Best Regards Josu?

Hi all, I have a connect between a siemens hipath & Asterisk system over PRI The connection works perfectly I can call from the Hipath to an Asterisk Extension. I want to allow the hipath extensions to dial out over a SIP trunk on asterisk but I keep getting "The number you have dialed is not in service" In this CLI I'm dialing from hipath extension 9 (prefix for sip trunk)

For all who are interested: A quick review of CeBIT 2005. :-) CeBIT was a very successfull event. Most of the time, the asterisk-booth was crowded with more people than we could talk to. We had with us a demo-installation including different IP-phones, digital and analog phones as well as a Siemens HiPATH PBX to which our Asterisk-server served as a VoIP-gateway, and many people were impressed

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

Hello. I am going through the documentation and trying to find if asterisk can help me in my case. It is quite difficult to find answer because I do not know the exact question. I have two location. Each in different country. Both locations have Siemens HiPath - different type and software. I can not use card that would allow me to connect those PBXs using SIP. But I have some free ISDN and

Hi all, i have asterisk 1.2.17 with sip tcp support and i am trying to connect asterisk with HiPath 4000 V.3.0 using SIP. I can see the registration from the HG3540. But when i try to place a call from Asterisk to HiPath, the call fails with SIP/2.0 603 Declined. The strange thing is that the first INVITE uses tcp and the response is a 100 TRYING, the next 7 INVITE are using udp and the respose

Apparently there are subtle diferences between meaning of MeetmeJoin event depending on channel type. Problem is: after originating a call from channel to MeetMe room i.e.: [meetme] exten => 1,1,Answer exten => 1,2,Meetme(kolejka|dqM) than: Context: meetme Exten: 1 Priority: 1 ActionID: 1077925740-00000004 Timeout: 5000 Action: Originate Async: true Channel: somechannel I get eventually

I downloaded asterisk to use cvs to checkout the release version. After installing, I would like to load module chan_h323.so but there is some error : *CLI> load chan_h323.so Feb 17 15:22:38 WARNING[2865]: loader.c:258 ast_load_resource: /usr/lib/asterisk/m odules/chan_h323.so: undefined symbol: __use_ast_pthread_create_instead__ Unable to load module chan_h323.so *CLI> How can I solve

Hello all, as good? It would like to make a question, asterisk supports the protocol qsig, for interconnections in ISDN with equipment Siemens HiPath 4000 or same Ericsson MD110, so that it could identify to the name and the number of hosts and also to use some features of asterisk in the Siemens/Ericsson equipment. Greetings Josu? -------------- next part -------------- An HTML attachment was

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get