similar to: TDM11B - 2nd channel is not detected

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

I am trying to reconfigure an asterisk box that was using an HFC-S card with bristuff but is now using 2 analog lines therefore I want to use the TDM02B to connect to two POTS lines. The TDM02B has 2 red modules. I have this in /etc/zaptel.conf loadzone=nl defaultzone=nl fxsks=1-2 I have /etc/asterisk/zapata.conf signalling=fxs_ks echocancel=yes echocancelwhenbridged=yes echotraining=400

Greetings all, I've just put two X100P cards to my box and despite trying everything I can find on the web, I can't get the second one to work. I've edited /etc/modules.conf so that ztcfg doesn't run automatically. To start, I run: /sbin/modprobe zaptel /sbin/modprobe wcfxo /sbin/ztcfg /sbin/modprobe ixj and ztcfg says: ZT_CHANCONFIG failed on channel 2: No such device or

hello, i have a problem starting asterisk with one x100p digium and two hfc chipset isdn cards with bri-stuff.0.0.2. "ztcfg -vv" shows me a this info: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02) Channel 03:

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

I installed TDM400P and X100P pci cards in a system running mandrake 10.1 official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running ztcfg and asterisk fails. [root@asterisk asterisk]# ztcfg Notice: Configuration file is /etc/zaptel.conf line 3: Unable to open master device '/dev/zap/ctl'

Hi, I have two WCT100P cards installed on a suse 9.0 box. Installation for Zaptel complains of some unresolved dependencies. The zaptel and wct1xxp modules load without any errors. ztcfg give no problems. The problem is when I start asterisk I get the following error and asterisk shuts down

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

After emerging some updates this morning asterisk 1.0.3 fails to start I get the following errors: ..Jan 6 00:39:24 WARNING[28998]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Jan 6 00:39:24 ERROR[28998]: chan_zap.c:6197 mkintf: Unable to open channel 1: No such device or address here = 0, tmp->channel = 1, channel = 1 Jan 6 00:39:24 ERROR[28998]:

Hello, This is debug output I get: Jul 28 15:05:49 WARNING[8249]: chan_oss.c:239 sound_thread: Read error on sound device: Resource temporarily unavailable [chan_zap.so] => (Zapata Telephony w/PRI) Jul 28 15:05:49 WARNING[8249]: chan_zap.c:924 zt_open: Unable to specify channel 1: No such device or address Jul 28 15:05:49 ERROR[8249]: chan_zap.c:6460 mkintf: Unable to open

Greetings I was getting bad static crackle on a phone, so I reload from the latest CVS and did a make clean ; make install on zaptel, libpri and asterisk Now I get this error [chan_skinny.so] => (Skinny Client Control Protocol (Skinny)) May 28 13:59:42 WARNING[16384]: chan_skinny.c:2541 reload_config: Unable to get our IP address, Skinny disabled Urgent handler [chan_oss.so] => (OSS

Hi, all I have installed TDM400 card. I can see it is there (lspci). But Asterisk does not find it. phonebox2*CLI> zap show status No Zaptel interface found. I assume that driver is not loaded, but I am sure I have installed it (I compiled zaptel and then re-build asterisk and did make install for both zaptel and asterisk). When asterisk is started I get: Jan 2 06:28:08 WARNING[3473]:

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

Hi List, I have a test asterisk box with a TDM400P with 4 FXO modules plugged in. Yesterday I could use the box without any issues - no problems. This morning, the sound on the box was absolutely horrible. After some fiddling about, I have rebooted the box, and now asterisk refuses to start! Here's the message I get: Jun 9 10:45:53 WARNING[3297]: chan_zap.c:769 zt_open: Unable to

Of course I am not a kernel expert, so .. please be patient. I am investigating on my zaptel/zapata problem. As the main error message asterisk quits on mentions <'/dev/zap/channel': No such file or directory> I went peeking over there. [Asterisk Verbose Error Mar 13 20:43:35 WARNING[5779]: chan_zap.c:763 zt_open: Unable to open '/ dev/zap/channel': No such file or

Im getting the following error when I try to start Asterisk WARNING[16384]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Nov 29 21:40:43 ERROR[16384]: chan_zap.c:6195 mkintf: Unable to open channel 1: No such device or address I'm using a TDM22B card. ============= # Zaptel Configuration File # loadzone=us defaultzone=us fxoks=1-2 fxsks=3-4 ==============

Can someone please help me with my config settings for my TDM12B. I have got the FXS port to work fine, but I cannot get asterisk to startup with any settings for the fxo ports. It appears to be something related to the message "Signalling requested is FXS Kewlstart but line is in FXO Kewlstart signalling". However, I have tried what appears to be every possible configuration option. I