similar to: IAX Freeworld

When I try to call out to FWD over IAX2 I get: Call rejected by 65.39.205.121: Unable to negotiate codec I'm using asterisk-1.0.5 (the same settings works fine with *0.9) I've standard settings in iax.conf [general] bindport=4569 register => xxxxx:xxxxxx@iax2.fwdnet.net [iaxfwd] type=user context=fromiaxfwd auth=rsa inkeys=freeworlddialup disallow=all allow=ulaw -- #Joseph

Hi, I cannot seem to accept incoming calls from FWD using IAX2. I followed the directions posted at www.fwd.pulver.com/advanced/iax I can make outgoing calls fine using IAX via FWD. When someone calls me from FWD I get the following message: Chan_iax2.c:5251 socket_read: Reject connect attempt from 65.39.205.121 Any ideas? Thanks, S.

Hi, I got my * working fine with FWD at office with 2 extensions, i receive calls and i can make calls thru FWD. I got also my * at home, and i connected it using auth=rsa. From my home, i can make calls using my office iax, but if i try to redirect incomming calls from FWD to my * at home, it rejects the call. I created the pub/key pairs for rsa and its working ok and i just pasted the

Hello all, Here is my problem, I try to place a call to FWD (free world dialup) trough my asterisk PBX. my config is as follow: extensions.conf ---------------- [internal] exten => 613,1,Dial(IAX2/iaxfwd-outbound/613) (service echo de FWD) exten => xxxxxx,1,Dial(IAX2/iaxfwd-outbound/xxxxxx) mon numero FWD exten => yyyyyy,1,Dial(IAX2/iaxfwd-outbound/yyyyyy) celui d'un ami FWD

I've searched WIKI and Archives but nothing. Im getting: -- Called username:password@iaxtel.com/1800somenumber@iaxtel Jun 21 17:04:12 WARNING[1158883520]: chan_iax2.c:5097 socket_read: Call rejected by 69.73.19.178: Unable to negotiate codec -- Hungup 'IAX2[Iaxtel]/8' == No one is available to answer at this time -- Executing Hangup("SIP/104-b8eb", "")

Hi, I had a FWD account set up with asterisk (using SIP) and it was working fine both ways. I switched to IAX2 and now I can't get incoming calls from FWD. People who call my FWD number get a "480 - user is not online" message without any traffic reaching my box. I can call FWD numbers fine over IAX2. It seems fwd isn't trying to place the call over IAX2 because it thinks

When somebody call me on my pstn # cable connected to my fxo card it does not work when I check my computer the following error shows Connected to Asterisk CVS-v1-0-12/05/04-19:46:25 currently running on asterisk1 (pid = 2160) Verbosity is atleast 3 -- Remote UNIX connection -- Starting simple switch on 'Zap/1-1' == Starting Zap/1-1 at incoming,s,1 failed so falling

Hello, I have 2 channels in iax.conf [iaxfwd] type=user callerid= Free World Dialup inkeys=freeworlddialup auth=rsa context=incoming qualify=yes [iaxfwd-outbound] type=peer host=iax2.fwdnet.net username=xxxxxx secret=*********** auth=md5 The problem is: When I tell FWD to call me I have this output in my asterisk consol: Executing Dial("IAX2/iaxfwd-outbound-3",

I am having trouble with this. I can dial 1800 numbers fine as well as FWD service numbers but not Vonage. I can be called from ipkall and fwd and can call aixtel numbers. I use aix2 with Fwd. My extensions.conf for Vonage: ; vonage numbers ; ; +2431 exten => _2431XXXXXXXXXX,1,SetCallerID,${FWDCIDNAME} exten =>

Hello, I am trying to setup my Asterisk box to accept calls from the FWD network. I've followed all the config advice / samples I've found on the web. Making calls to devices on the FWD network from my Asterisk box works flawlessly, but whenever I try to call my Asterisk box from a FWD client I get a busy signal, and a "Call Disconnected" 486 error. What's odd is that I

============= SJphone Log ============ Outgoing SIP session Respondent: (sip:8612@192.168.2.2) Remote client: Started: May 26 16:33 Accepted: no Ended: May 26 16:34 End reason: Call rejected: 503 Service Unavailable =============== Asterisk Debug ================ Executing Dial("SIP/2201-a83e", "IAX2/<FWDNUMBER>:@iax2.fwdnet.net/612|60|r") in new stack --

Hi List; If I need to do a trunk between Asterisk and another SIP softswitch (so Asterisk will send a SIP calls to that softswitch), then I have to configure this on the sip.conf file or where exactly? And is it the same when I configure iax trunk? Should I determine the context in this case for this SIP trunk? Regards Bilal

I've setup my IAX2 over FWD and it is working I can receive a test call and I can call out. Though I cannot figure out how to dial 1-800 numbers over FWD When I dial 1-800 it hangs up on me. Here is a typical session: Called xxxxx:xxxxxxx@iax2.fwdnet.net/18007425877 -- Call accepted by 65.39.205.121 (format ULAW) -- Format for call is ULAW -- Hungup

I have set up FWD via IAX service. I have tested the IAX service with 613, echo test, and 612, saytime. It all works well. However when ringing a FWD user, I got this error all the time: Connected to Asterisk CVS-v1-0-02/01/05-09:34:45 currently running on chat (pid = 8282) chat*CLI> Verbosity is at least 3 -- Executing SetCallerID("SIP/1001-a1fb", ""David

Im trying to get IAX to work between my * and FWD. I activated my iax2 account on iax.fwdnet.net and I get the output: "Registered to '65.39.205.121', who sees us as 68.14.203.254:4569" when I start asterisk. I tried used the Call Me tool on fwdnet.net but I dont get any calls even though the Call Me tool says everything looks ok. Can someone call my FWD number and just leave

I have configured iax.conf and extensions.conf as instructed on FWD website (http://www.freeworlddialup.com/help/?p=knowledgebase&c=18&a=76) and I can successfully receive calls and make test calls to 612, 613, etc. The problem is that I can not make a call to another FWD user. Here is what asterisk says: -- Executing [393xxxxxx@default:1] Set("Zap/1-1",

When I use DISA I get congestion when I try to reach 1-800-number: Here is the context: [disa] exten => 087,1,Answer exten => 087,2,DigitTimeout,8 exten => 087,3,ResponseTimeout,20 exten => 087,4,Authenticate(985) exten => 087,5,DISA(951|disa-access) [disa-access] include => tollfree include => outgoing-voipjet [tollfree] ; ; terminate toll-free no.'s via fwdnet ; US

I'm trying to test IAX2 with FWD It registers fine but when I try to receive the call I get: chan_iax2.c:476 iax_error_output: Ignoring unknown information element 'Unknown IE' (38) of length 1 Jan 25 18:02:12 WARNING[114696]: chan_iax2.c:476 iax_error_output: Ignoring unknown information element 'Unknown IE' (39) of length 1 Jan 25 18:02:12 WARNING[114696]: chan_iax2.c:476

Guys. Im using IAX and FWD and I think everything is setup fine.. someobdy just tried calling me but my phone jus ran once and sent them straight to the voicemail.. the logs show this: -- Accepting AUTHENTICATED call from 65.39.205.121: > requested format = ulaw, > requested prefs = (), > actual format = ulaw, > host prefs = (alaw|ulaw|ilbc|gsm),

Is there a Centos equivalent to the Fedora freetype-freeworld? -- MELVILLE THEATRE ~ Melville Sask ~ http://www.melvilletheatre.com