similar to: void your warranty and get a 3.3V/5V TE405P

Can anybody tell me the difference between a TE410P and a TE405P? Is it JUST the 5v vs 3.3v pcis slot spec, or is there some thing else? </edg>

I'm having some trouble here - need some help! I've just bought a TE405p (32-bit 5V), but cannot get it working in a dell 6450. The dell has (from tech specs) "three peer PCI buses: two 64-bit buses and one 32-bit bus Expansion slots seven hot-pluggable PCI slots (two 64-bit/66 MHz, four 64-bit/33 MHz, and one 32-bit/33 MHz)" I cannot get the card working in any of the slots.

Anyone care to elaborate on the differences between the T400P and the TE405P? -Darren -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050908/e817f8bb/attachment.htm

Hi, I just bought the E100P from digium. It has both keys: 3.3V and 5V, so it would fit both, in a 5V-PCI slot and in a 3.3V PCI slot. Is it true, that I can plug it without destroying it in an ordenary 5V PCI slot? Roger.

I am getting ready to purchase my first Digium card to start experimenting with Asterisk. Before I make my purchase, I wanted to make sure I'm not going to have issues with these cards (need to see what the specs are on my box, 5V or 3.3V PCI ). I will be using Asterisk @ Home, so will be Asterisk v1.0.9. I took a quick poke at the lists, and it appears several people have been having

Hello, I'm looking at building a couple new PRI Gateway boxes using TE405P cards, and was wondering if anyone has had any experiences (good or bad) with the Intel SE7210TP1_E motherboards from Intel. General Technics builds some really nice (and cost effective) 1U servers based on the board: Server: http://www.gtweb.net/gt637.html Specs:

Hi, Urgently response would be wonderful, system is a Fedora Core 2. I have a Ericsson BP250 connected to 1 port on the TE405P and another connected to a local telco ISDN30. I have been running CVS-HEAD from about a 2 months ago and upgraded it again just in cause it was a version issue (didn't fix it) but this is what I am getting. When a person calls out from an extension on the BP250 to

Forget the sound card. It isn't related. The subject above should have read 'TE405P No Voice Problem' or something similar. It appears to be a zaptel timing issue, but I have found a workaround. For those of you just tuning in, here is the story: I have a CentOS/Intel 865 box currently running Asterisk 1.2.7.1 and zap 1.2.5, both compiled from the source available off the main

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

> - set sampling rate to 8 kHz (at least for now) > - make sure the far end signal in the playback signal is always a bit in > advance (never late) compared to the mic signal. > - Set the tail length to something around 100 ms. > > Also, if you're using two different soundcards (as I understand) for the > playback and the capture, you're *never* going to get echo

We originally purchased a TE405P so we could connect our Asterisk server directly to the T1 PRI from our provider, however due to all the problems reported with T1 PRI's interacting directly with Asterisk, we scrapped that idea and decided to stick with our Cisco router making the conversion to SIP. Anyways, we found a new potential use for it. We have an old location with an existing PBX,

Dear users: I have bought TDM04B card and it works in PCI 2.2 ver. slot. How can I check if specific mother board support PCI 2.2 ver. I do not have any documentation for that motherboard. B.

This works fine. Message: 26 Date: Tue, 7 Jun 2005 17:22:23 +0800 From: "Ma Zhiyong" <mazhiyong@sohu.com> Subject: [Asterisk-Users] te405p and dell poweredge To: <asterisk-users@lists.digium.com> Message-ID: <004501c56b42$6a12fcd0$7301a8c0@hylaclient> Content-Type: text/plain; charset="gb2312" Hi, I want to install * and te405p on Dell Poweredge 1850. Can I

My Asterisk server believes that a Digium TE405P and sound are incompatible. Basically, no matter what else I do to the machine it terms of hardware, if the TE405P is installed, none of the playback/background/etc commands work. MOH works fine. So far, I have tried: 1) Seven different PCI soundcards with different chipsets. (Go go Computer Junk Store!) 2) Disabling each and every device

Hi I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after putting in the upgraded board but did not change any conf, but the spans become active but will not come up. I guess I am missing something or are the any changes to the zaptel/libpri software that is required. I cannot find any info about this or does this new firmware only work with latest CVS. I am using 1.0.9 with

Hi Everybody, Is there anyone who already uses Asterisk with TE405P card? Is this card going well with the old E400P or T400P drivers? Are there a lot of differences? In the card's data sheet writes this sentece: "Digium has designed the TE405P to be fully compatible with existing software applications..." Is this meaning the the old drivers are also OK for this card? Thank you

Hello, I would like to know if FreeBSD has drivers for TE405P cards submitted to the ports. I have acquired a card and would really like to use it with FreeBSD. The wiki said the drivers havent been tested yet. Have there been any updates since then? regards Kavit _______________________________________________ Asterisk-Dev mailing list Asterisk-Dev@lists.digium.com

Hi, I want to install * and te405p on Dell Poweredge 1850. Can I do that successfully? Any one has successful experience on that scenario? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050607/fb7408a1/attachment.htm

Hello, We use all SCSI PCI card hardware RAIDs on all 4 of our production Asterisk servers. They all have Digium quad T1 cards and they all have from 2 to 4 T1s hooked up to them. We have had no noticable problems with dropped calls/poor quality. What are you looking to do with this system? what kind of traffic will be going through these 4 T1s? MATT--- -----Original Message----- From: Deon

Why PCI 3.3V for E1/T1 card!? I can not use it because I can not find any motherboard with PCI 3.3 . Any sugestions!? Cristian VASILIU AccessNET International S.A. Software Programmer mail to :<cvasiliu@accessnet.ro> www:<http://cvasiliu.home.ro>