similar to: Problems with ADIT600 and T100P

I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part

Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the command line. The slots (3 fxs) are configured with 'ls' signaling. I configured the T1 card with the same line settings as the T1 interfaces on the adit and I get green lights on both the T1 card and the T1 interface on the adit (so

Hello, I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to my * server via T100P card. This is the output of "status equipment" command in the Adit600: For some reason the FXO card is seen as FXS, why? Is it ok? On the card it is written "FXO". Regards, Shlomi Bachar -------------- next part -------------- An HTML attachment was

Has anyone ever heard of this so called Dynamic Impedance matching on the ADIT 600? I called their support and they've never heard of it. We are of course having echo problems are on the far end due to digital/analog conversion on the local end using a channel bank. We have purchased an ADIT 600 and yes the complaints are "far less" however we're still getting them. While I have

I am hoping to replace my Nortel 8x24 switch with Asterisk. Right now my cabling comes from my outside phone box into my office and into a punchdown block and leaves the punchdown block as an amphenol connector which currently plugs into the Nortel swicth. A second amphenol connector them plugs into the switch and extends to another punchdown block that I believe carries the lines throughout the

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

Hello All, Just a question, I have an adit600 and I am looking for a way to pull the incoming cid into asterisk. Does anyone know if this is just not possible via t1? Or is it only available on PRI? Thanks, Greg

As soon I do a reload I see contant ringing like this on the CLI: -- Zap/14-1 is ringing -- Zap/23-1 is ringing -- Zap/22-1 is ringing -- Zap/20-1 is ringing -- Zap/19-1 is ringing -- Zap/14-1 is ringing -- Zap/23-1 is ringing -- Zap/22-1 is ringing -- Zap/20-1 is ringing -- Zap/19-1 is ringing This goes on continuously and no phones are ringing. I am using a digium T1 card and ADIT 600. Does

Hello, I don't have any experience with channel banks and would appreciate any feedback on my theory outlined below: We have a single T1 entering the building with channels 1-12 being voice lines and 13-24 being a 768k internet connection. This T1 terminates to an Adit 600 (T1-1). Here's what I know. Channels 11-12 go out the Adit 600's 25-pair connector to a wiring block (and

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

Hi ! I am connecting to Adit 600 thru a T100P card I have configured 1-16 FXS channels and 17-24 FXO. Everything looks fine on Asterisk side I get a tone on all FXS channels, but when I try to dialout thru one of the FXO channels 17-24 it doesn't connect to the POTS line and echoes back my voice. I use fxsls and fxols for the T1 channels and ls on Adit side. Whats wrong here ? here is my Adit

Can someone recommend a good quality 24 or greater port channel bank? Steve -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070506/e5896021/attachment.htm

Hi guys, I've run into a problem that I can't figure out on a bunch of handsets I have running into a Rhino Equipment 24-port FXS channel bank hooked up to a T100P and running asterisk-0.9.0 and the associated stable Zaptel release. The sidetone (your own voice that you hear in your handset, built in for comfort) is noticeably louder than it should be, and it doesn't seem to

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

Hello, I will be setting up two asterisk systems and I'm looking for some suggestions as to what the best way to do this will be. The 2 systems are for 2 companies that share a single T1 line. The T1 line has 12 voice channels and 12 data channels. Currently, they are set-up as follows: T1 line from provider enters CSU/DSU and splits voice/data channels. The voice channels are sent to

Just starting to do the research on this one....I've got a customer who is showing interest in replacing any older Panasonic unit providing service to 96 tip/ring lines from a single PRI. Does anyone have any recent experience with a decent (as in, plays nice with * and has a reasonable per-port cost) channel bank or similar? Mediatrix only goes up to 24 port, as far as I can tell, which

Here's our config: cisco 7960's running 6.3 sip code latest cvs of * t100p zaptel card adit 600 channel bank 7 pots lines and 2 fax machines on the adit 600 dialing out from the cisco phones gets sent out via the zap channels, but I'm having some serious echo problems. I currently have the adit set to +3 rxgain and -6 txgain, with my zapata.conf containing: echocancel=128

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

I'm having issues with echo. My setup is Polycom IP501 phones connected to an Adit 600 via T100P. 13 Lines going to the Adit. All echo so far is on the local side (Employees hears own voice, but only on some calls). Watching the channel with ztmonitor, I notice that TXGAIN is pegged out most of the time. RXGAIN is anywhere between 45 and 60%. Is it safe to assume that playing around

Jon, I actually had some more discussions with Tim on this issue, and it seems that the channel bank would still be a good option to choose for internal purposes. I would not see any other solution than a channel bank to connect many 2wire phones into one asterisk box. I had a talk today with Carrier Access, and it seems that the adit would do us fine. The fxs cards of the adit 600 are