similar to: TDM400 seems healthy, but no dialtone??

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

G'day all, A weird problem has just started happening with my * server, and I've googled myself stupid looking for help. My system is latest CVS, a TDM400P with two FXS modules, two X101Ps, and VoIP connections (SIP, SCCP & IAX2). My wife complained about her extension (analogue, on one of the TDM400 ports) being dead -- no dialtone. I had to shut down *, then unload and reload the

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

Hello! We are using the Digium 405PP card, and getting the following messages: Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 6 on Primary D-channel of span 1 Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 8 on Primary D-channel of span 1 My config file is below. We are trying to set up D-Channel on channel 24, 1-23 in trunk group 1,

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel

Hi! I'm struggling with pam_mkhomedir. Accounts are stored in LDAP (CentOS Directory Server AKA 389 Directory Server). I am not pre-creating user home directories, and would like to use the pam_mkhomedir module to create the directories on the fly, when a user is authenticated via pop3s. pam_mkhomedir is working for interactive (e.g. SSH logins), but I don't want to require users to

Okay, I'm going to preface this by saying I'm sure I've overlooked something really basic here. I just need someone to hit me with a clue stick and point out what I'm missing. I've got a TDM card with four FXO modules. I've plugged one of them into a PSTN line. I'm working through the examples in the Asterisk Documentation Project guide, but I can't get Asterisk

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Steve, Here is the config, I pulled from my server, that works with D'Link Phones: Main Menu -------------------------------------------------------------------------------- SIP.CONF [general] port = 5060 ; Port to bind to (SIP is 5060) ;bindaddr = 0.0.0.0 ; Address to bind to (all addresses on machine) bindaddr = 67.109.153.236 disallow=all ;allow=ilbc allow=gsm allow=ulaw

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

Callerid issue 1) if you run ztmonitor on the fxo line & call in do you hear the fsk tone if yes then we beleive the CAC is passing fsk 2) in chan_zap->ss_thread around line 4154 (current cvs) if you get to the callerid_feed at least once then if you get to chan_zap->ss_thread->callerid_get around line 4163 (current cvs) does this parse fail

Folks, I have a Xen Asterisk VM with a TDM400 card. When I try to run dahdi_cfg, I get: tempest:~# dahdi_cfg -vvv DAHDI Tools Version - 2.2.0 DAHDI Version: 2.2.0 Echo Canceller(s): Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Echo Canceler: none) (Slaves: 01) Channel 03: FXS Kewlstart (Default) (Echo Canceler: none) (Slaves: 03) Channel 04: FXS

I have a TMD400 card installed in a PC with one fxs (installed in slot 2) and two fxos (installed in slots 3 & 4).? fxos work fine but I am unable to get a dial tone for any devices connected to the fxs.? I have correctly connected the power supply to the card and I have even tried moving the card from slot 1 to 2 on the board. Below is from the console when I try to route a call from FXO on

Hi All, I cannot get my TDM to work correctly. In my /etc/zaptel.conf file I have loadzone = us defaultzone=us fxoks=1 In my /etc/asterisk/zapata.conf file I have [trunkgroups] [channels] context=from-pstn usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes cancallforward=yes

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

Hello, is there a full guide to what kewlstart is supposed to do with FXO or FXS lines ? is it only applicable to one of the interfaces FXO -or- FXS but not both ? I asked earlier if FXS lines can be made to reverse polarity, and someone else pointed out that the chipset on the FXS ports seems to support it, perhaps the driver in the asterisk zaptel interface module needs to be modified to support