similar to: Strange T1 Problem - FIXED plus new question

Displaying 20 results from an estimated 10000 matches similar to: "Strange T1 Problem - FIXED plus new question"

2004 Jul 23
6
Robbed Bit T1 Configuration
Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial
2004 Apr 15
7
Strange T1 Problem
When people call into my * box over the T1 interface, they get no ring tone. It rings the SIP phone and when the SIP user picks up, both parties can hear each other ok, its just the PSTN user calling in hears no ring. What could be causing this? I tried setting immediate to yes in zapata.conf, but that causes my DNIS and CallerID to stop being available. T100P with E & M Wink start
2006 Apr 03
4
R2 protocol error
Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier
2004 Apr 15
2
T1 Line install.. (UK Muppet)
Hi all, Muppet from the UK asking for help We are just about to have a T1 line installed in our office in Dallas and "Advantex" the supplier has sent a questionnaire asking a number of questions. I have put the question area at the bottom of the email, we will be using Digium's hardware. could anybody help :-) In the UK when I asked for a E1, number of trunks required and the
2005 Aug 22
1
Asterisk ISDN CallerID identification failure
Hello, We have 4 'Onramp-2' Telstra ISDN BRI services operating on Asterisk Server with Eicon 4BRI card. For most part the service is okay. However, we are are having problems with passing callerID to internal extensions. This is the set of command executed. exten => <pattern>,1,Answer ; Answer the line exten => <pattern>,2,NoOp(${DNIS}) ; debug statements exten =>
2005 May 16
3
CLI and DNIS presented to Analog extension
My company is based in Australia and we have a need to be able to present CLI (ANI) and DNIS to an analog extension. Currently our PABX vendor is saying they can only deliver CLI between the first and second cadence. The system will collect calls via an aggregate of ISDN PRI services from the PSTN and then direct them to the analog extensions in a hunt group configuration. It is important that
2004 Jul 03
1
Caller ID and DNIS Problems (Non-Pri T1)
I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800
2007 Feb 16
1
DNIS on T1 channels
I installed a Sangoma card with the default install. I'm getting five digits of DNIS with each call. The T1 is setup ESF/B8ZS wink start. Each of the digits of the DNIS are being used for extensions in the context. I need a single extension that let me start an AGI script that can use the dnis. Can anyone point me in the right direction to do this? Thanks, David Ruggles CCNA MCSE (NT) CNA
2010 Mar 08
1
Turning off DNIS on T1 set to FXO_LS protocol
Hello everyone, Our company has an Asterisk server where one of the T1s is connected to an IVR. Asterisk is configured for FXO Loopstart, and the IVR is configured FXS. We can call into it, but our software doesn't expect DNIS digits on FXS, and the digits are being interpreted as user input. We can certainly change our software accordingly, but our test bed also includes other
2006 Jun 17
0
T1 + E&M
Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system
2007 Jun 14
2
Unicall + MFC/R2 line dropped immediately after connect
Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but
2005 Aug 22
0
Does Asterisk support T1 E&M Wink/Wink voicechannels on any Digium/Sangoma hardware?
I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable
2004 Sep 23
2
CallerID on Channelized T1 not working with 1.0.0
I have been using Asterisk 1.0-RC2 successfully with a channelized T1 circuit for quite a while now but after upgrading to 1.0.0 callerid no longer works properly. Debug output from a channel shows what actually is received through DTMF from the carrier: << [ TYPE: DTMF (1) SUBCLASS: * (42) ] [Zap/9-1] << [ TYPE: DTMF (1) SUBCLASS: 2 (50) ] [Zap/9-1] << [ TYPE: DTMF (1)
2004 Sep 25
3
Non-PRI T1 configuration
I'm trying to hook up a non-PRI fractional T1 using a T400P port. The Telco says that it is provisioned as AMI with SF (not ESF) and that they are signalling by "sending down a straight DS1" (I'm not sure what exactly that means). They are also sending DNIS over these channels. I currently run it through a channel bank for my IVR application and it works fine but I am now
2015 Jul 12
2
Why no support for 3-digit HEX colours?
When specifying an RGB colour in R, is there a strong reason not to accept 3-character HEX codes? In CSS and many other languages, a colour of "#ABC" is automatically converted to "#AABBCC", and I was wondering if R could support that as well, or if it was a conscious decision to not support it. --- http://deanattali.com [[alternative HTML version deleted]]
2005 May 11
0
T1 Card ------ Adtran ------- FXS BUG???
Good Day list, I have googled and wiki'd myself to no avail. Here is my setup. Asterisk Box Digium T1 card connected to an adtran Total Access 624. I need to pass ANI and DNIS information from asterisk to the analog devices hanging off the adtran. The digits are announced to the fxs devices between ring 1 and ring 2 (If I pick up the anlog phone after ring 1, I can hear them so I
2005 Jan 18
1
Asterisk - libunicall - MFCr2 *** settings problems ??? ***
Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors
2004 Apr 13
2
T100P E&M Wink Trunk
I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound
2005 Jun 13
2
T1 multiplexer (or ?) for failover in large installation
Hi, Please forgive my terminology, still a bit new to T1s and such. I'm looking for a way to have 5 T1s from a carrier terminate into some type of box (multiplexer?), then be able to plug 7 asterisk servers into that box (each with single port T1 card) and be able to have 2 * servers go down at any given time and not actually have the carrier see that anything has happened. Obviously if a *
2009 Mar 19
0
T1 signaling configuration
Hi All, I'm trying to configure a Digium T100P to talk to a legacy voicemail system. I have the signaling specs verbatim from the original manufacturer documentation as follows: [T1 Signaling] Service Type: T1,D4 format, AMI(Super Fram) Signaling: Four wire, terminated, E&M (Robbed bit) Start Protocol: Wink start; 250msec duration Dial Tone: Enabled Digits: DTMF, 4-digits DTMF: 50msec