similar to: FXO cards for TDM400P....

And if you want to use it with windows telephony software, such as answering machine or modem communications software, you can probably take the drivers for the Intel MD3200 based modem, modify the .inf for the Digium vendor and device ID. I have not tried this, but since the MD3200 modem works that way in Linux, the X100P may work that way in Windows. Then you would have a $100 winmodem! Let

> Hi! > >> We are in the process of an Asterisk call center deployment using IAX2 >> G711 ulaw softphones. Outbound sound quality is terrible. RESPONSE: This is Bill McCready from PCPhoneline.com . To address your sound quality issues, you may want to check out our VTA1000 Skype+SIP+IAX2 Tri-Mode Gateway which plugs into the USB port of a Windows computer. You can use it

Hi all, I have a question that I was hoping someone could answer for me. I would like to find a USB phone that works with Asterisk... preferably one that does not have any issues with NAT. Can anyone point me to something suitable ? We are essentially planning to do a beta for a few hundred customers on our network and would like them to be able to call one another @ no charge. Because

Hello all asterisk users! Question: Does anybody know about any good USB handset that would understand SIP and Asterisk and will run with Linux? I have found tons of them, but they are mainly only supported in Windows environment. I would like to set up new phone system in our company that would be based on asterisk acting as PBX and SIP. If you have any suggestions, please let me know. Any

http://www.pcphoneline.com/skype "The VPT1000 is NOT a simple last generation USB phone audio device but is rather a next generation integrated gateway and USB phoneset with simultaneous dual mode Skype and SIP calling support. Skype is not forecast to have "SkypeIn" available until June 2005 but you can have the capability now via its built in SIP capabilities." Is this a

Greetings, This may be a bit arcane but does anyone know what the contents of a facility message should be for initiating a TBCT on an NI2 ISDN. I've been trying to get it to work on a DMS100 for the last four months to no avail. The message I am currently sending makes it to the switch but is returned with unknown message. Perhaps someone here has done it before and can help me out.

Hey Everyone, We are in the process of reviewing headsets for use with our GXP-2000s. I'm looking for some feedback as to which headsets people are using, the pros and cons of those headsets, and if they would recommend them to someone else. Any help would be appreciated... - Jason -------------- next part -------------- An HTML attachment was scrubbed... URL:

Folks: I'd like to install Asterisk for use in my home. However, I'd like to continue using wireless phones in a couple of locations. The cheapest way to do this is to continue to use analog phone devices via an FXO/FXS box. However, I am not clear on whether I can expect these devices to provide "call waiting" features and caller ID features to the connected analog phone.

I have quite successfully set up the Services button to work on the 7940 running SIP. I have a metric-imperial converter, a foreign exchange rate calculator, a calendar etc available to users. The XML is really fussy though. Simon -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Rich Adamson Sent: Thursday, 1

Voxilla news story: http://voxilla.com/voxstory84-nested-order0-threshold0.html Two new products * A Sipura 2000 in a linksys box: Linksys PAP2 Phone Adapter * A combination NAT router with 2 FXS ports: Linksys RT31P2 Broadband Router Jim James H. Thompson jht@lava.net

Hi People, Ok i've tried everything I can think of but cant get this to work. Can someone please give me an example of their sip.conf settings and also the details of the settings in their grandstream phone to allow: 1. Grandstream phone to register with asterisk when on same lan. 2. Grandstream phone to register with asterisk when phone is behind a nat. Regards, Aaron.

Does anyone know if there are any plans for Zapata or anyone else for that matter to come out with a 3.3v PCI version or PCI-X version of those cards? Gene

Had a good question for the list, it seems whenever I work in an Asterisk console or on the machine normally I get jitters on any audio going through it. Especially if you did file copies or a 'ps ax' for example. I was wondering if there was a proper way to 'nice' the asterisk proc's? Cisco does this for example to it's "EXEC" and icmp processes, I tried

Hello All I am looking for a PC based switchboard application. Cisco CallManager has a web attendant console that allows you to use the PC to transfer calls and the like and I was wondering if there was a similar program compatible with *. Thank you in advance Keith D'Atrio -------------- next part -------------- An HTML attachment was scrubbed... URL:

I can't seem to make the fax detection work. Here's an excerpt from zapata.conf: signalling=fxs_ks group=0 context => guestaccess channel => 47-48 and from extensions.conf: [guestaccess] include => incomingmain [incomingmain] exten => s,1,Dial,Zap/1&Zap/9&Zap/10&Zap/11|24 exten => s,2,Voicemail,u7000 exten =>

Greetings, Below is part of the contents of my extensions.conf file. exten => s,1,Wait,1 ; Wait a second before answering. exten => s,2,Answer exten => s,3,ResponseTimeout,10 ; Set the amount of time the user ; has to make a selection. exten => s,4,DigitTimeout,5

Greetings, I have just purchased several Astra 390 phones ready for asterisk. I have placed a line with adsi=yes in the Zapata.conf file just before channel => 13 I have also added an extension exten => 6199,1,ADSIProg(asterisk.adsi) exten => 6199,2,Hangup in the extensions.conf file. When I try to program the phone I get the following: Asterisk CVS-03/28/04-12:02:10,

Has anyone had any experience using asterisk for a 911 call center? Does anyone know of any reason why it would not be suitable? As far as I know all 911 call routing takes place at the CO switch so a regular T1 line should work fine. I understand that there is support for ACD in asterisk and that is should be possible to implement screen pop (CTI). Any comments? Gene Kochanowsky Solution

Greetings, This is probably some configuration issue, but for some reason my system has stopped playing a ringing sound when an extension is dialed. The phone rings but there is no ring sound in the ear piece. Gene Kochanowsky

Is there any way to receive and send faxes using a T100 card? If so how is it done? Gene Kochanowsky Solution Sciences, Inc.