similar to: No ringing tone with IAXY (and other bits and bobs)

Hi List, I have this good looking IAXy device... I have managed to provision it, i can see it registering to my asterisk box, however when I pick up the phone which is plugged in the IAXy I have no dialtone, nothing. Any ideas what might be going on? Cheers, Jean-Michel.

iH i have an IAXy which i can make calls from but am unable to call. when i dial the extension assigned, i get the following from the console; -- Executing Dial("SIP/5801-b665", "IAX2/5899@192.168.0.5") in new stack -- Called 5899@192.168.0.5 -- Call accepted by 192.168.0.5 (format ULAW) Nov 1 12:28:33 NOTICE[163850]: chan_iax2.c:5546 socket_read: Rejected

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

Hi all, getting a server going wiht a few TDM400's and some phones, and some IAXys too I haven't heard any issues about AU phones being able to RING in Australia, like the problem in the UK with ring capacitors on the BT system. Are there any problems like that? Also, with the iaxy's -- they should work (and ring) in Australia right? The only hint I'm seeing around is the use

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

I just bought a new IAXy box and am only achieving one way calling. Both iax.conf and the IAXy support ulaw and gsm. When I try to call, however i get this error: Feb 11 15:20:32 NOTICE[7963]: channel.c:1893 ast_read: Dropping incompatible voice frame on IAX2/iaxy-2 of format ilbc since our native format has changed to ulaw I added support for ilbc on the IAXy and in iax.conf and am still

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

Hi all, I have a Soekris net4801-50 board with OpenBSD 3.9 where I've configured a dhcp server and tested it with a regular PC connected directly via a crossover cable with success. The problem comes when I try to connect my IAXy device instead of the PC. I can see with 'tcpdump -nettti sis1' that the IAXy isn't sending any packets to the dhcp server. I thought my IAXy was bad

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or

Hey Everyone, I recently purchased a few IAXy units for some testing, and have come across a some problems. One of them can be provisioned but will not ring the connected telephone. It also does not provide a dial tone when you pick up the phone. When a call is made to the IAXy one of the green lights on the board goes from a solid on state, to a flashing state that coincides with the

Yesterday I was using one of the cheap Radio Shack phone polarity on various phone outlets in my house and ended up plugging it into my IAXY. While the regular phone jacks tested OK, the IAXY tested as being reverse polarity. The tester was plugged directly into the IAXY so there is no chance of this being caused by crossed wires. Is this something that is misconfigured on the IAXY, a hardware

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

In the mailing list archives, I found a message that indicates that the IAXy has the ulaw, alaw, and g726 codecs, but I cannot find anything official on Digium's site about it. The Installation Manual has an example iax.conf file that indicates the ulaw codec, so I know that one is good. But we are thinking about using the IAXy over a VPN, to replace our MultiVoip. alaw and ulaw are

I place a call from an IAXY to an IAXY device. INitially the calls show in the output of "show channels". Then after a few seconds the "show channels" command shows 0 active channels even though I am still talking on the channels. Any ideas on this? THanks, Jerry

Hi, hoping that experienced hands will quickly show me the right way: after a fruitless web search i am turning to this list with my rather elementary question: is there any other way to communicate with the IAXy besides using special utility software that needs to be compiled under UNIX? Here is the story: about two months ago, after some not very satisfactory attempts at using SIP (my phone

There is no DNS functionality built into the IAXY, I am assuming you want to be able to home onto a SOHO site with a dynamic IPaddress. I have not been able to figure out a clean way to do theis (make it easy for the roaming sales-folk etc,) who will not have a high tolerance for running something like an IAXYPROV. You would need to somehow have an external fixed address which would

I have been searching for a while and can't find anything specific like this. Here's is my setup: IAXy -- broadband network -- Asterisk -- TE110P -- Channel Bank -- POTS lines (FXO) Everything works fine except for the echo at the IAXy. There is no echo on the POTS end, so Asterisk is doing a good job of echo canceling. Is there any provisioning in the IAXy to do echo

I've heard comments about the instability of the IAXy (loosing IP, locking up, etc) . I want to deploy some, in a remote site. The comments on the instability suggest that the simplest approach is to power-cycle them when you have problems. The IAXy would only be in use from 3PM to 8 PM. My potential simple solution is to have a timed power brick (like what you would use for a block heater)