similar to: Channelized T1, T100P problems

Hello, I have a T1 (not PRI) plugged into my Asterisk server. Everything is working well, except I only get the first digit of the 4 digit DID in Asterisk. The T1 provider (Eschelon) tried switching to 7 digits, and I only got the first digit of the 7. Can anybody help? We're adding another DID and I need to trap it correctly. Thanks. Here are snippets from the relevant files: --

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

I have been experiencing a rather odd issue with my (newly connected) T100P card. It is installed in my Asterisk server, which is working great with SIP clients. The card is connected to a channelized T-1 line (24 channels). The odd bit is that outgoing calls (Asterisk --> T-1 --> PSTN) works just fine. However, incoming calls (PSTN --> T-1 --> Asterisk) are dropped after about 20

Hi, I am fairly new at working with Asterisk. I am having a call quality issue that I really need to get ironed out before we go to rollout the system in a week. Any help would be greatly appreciated!!! Even if it is just pointing me in the right direction. My current setup: I have Asterisk Setup on a Dell Server. It has 2 T100P cards. One will be for out T1 PRI from the Phone Company (We

I have a problem which I need to resolve. We are trying to put an asterisk between a Mitel PBX and the world. We are adding Voip service via Asterisk. Here is are config files for the settings but our problem is the following. We are able to send calls to the Mitel pbx and it's the T1 connections is green saying it's ok. The support department from Mitel said that they use e&M and

We have contracted with Eschelon to provide voice and data over a T1 link. The plan is to terminate this link at a T100P card in the * system. The vendor has said that they will provide the D channel "contiguous to the voice channels" (voice on channels 1-8 and D channel on 9). The data channels would be 20-24. Will the T100P be able to accept this configuration? Does the PRI

Hello, I have a T100P card on a Red Hat 8 machine with Asterisk installed on it and I'm trying to get the data routing properly through it. I purchased an Integrated Data/Voice T1 Line with channels 1-6 voice and 13-24 data. The line is plugged directly into the Asterisk machine's T100P card. Previous to the asterisk set up we had an Adtran router that connected everything to what the

Hi All: I'm a newbee to Asterisk. I currently working on a project and want to know if Asterisk does support R2 Signaling. Thanks Begra8fl >From: asterisk-users-request@lists.digium.com >Reply-To: asterisk-users@lists.digium.com >To: asterisk-users@lists.digium.com >Subject: Asterisk-Users digest, Vol 1 #3647 - 9 msgs >Date: Tue, 04 May 2004 13:32:00 -0500 > >Send

Hello Everyone, I am new to asterisk and linux too, I managed to installed asterisk on redhat8 with the help of mailing list archives and Handbook guide. I configured 2 SIP phones (grandstream) and it is working fine internally. We have T1 Line coming in with block of 200 DID Numbers. I want to assign DID Numbers to each of SIP phones as an extensions and able to call any PSTN line.

> -----Original Message----- > From: Jerry Geis [mailto:geisj@pagestation.com] > Sent: September 8, 2004 2:19 PM > To: asterisk-users@lists.digium.com > Subject: [Asterisk-Users] T100P calls with playback starts speaking > before pickup > > > Hi > > I am using a T100P connected to a panasonic phone switch using T1 and the > switch has 4 analog lines

I am connecting a t100p to a b8zs, superframe, loopstart t1. Previously I've attached to e&m wink and pri lines with no problems; however I seem to be missing something. Should it be fxols in the zaptel.conf (smartjack to x100p) or fxsls? With e&m wink the dnis set was 100, so it was easy to make an extension 100; and it would answer incoming calls. How do you get a loopstart to

I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound

I ran into a couple of odd problems with a new Asterisk box I have set up... I have a T100P connected to a channelized T-1 (24ch) to the PSTN. The T-1 is set up properly so far as I know and seems to work perfectly with one exception: When a call comes in, asterisk starts a 'simple switch' for it, goes through my 's' extension progression until it gets to the first Playback

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

Hi All, I'm trying to configure a Digium T100P to talk to a legacy voicemail system. I have the signaling specs verbatim from the original manufacturer documentation as follows: [T1 Signaling] Service Type: T1,D4 format, AMI(Super Fram) Signaling: Four wire, terminated, E&M (Robbed bit) Start Protocol: Wink start; 250msec duration Dial Tone: Enabled Digits: DTMF, 4-digits DTMF: 50msec

my target is to produce a linux router with T100p to Fract T1 24chan to ethernet and TDM 4channel FXO. I have not been able to get nethdlc to work, just get zaptel networking not configured if I set bchan and dchan the card comes to life, but I don't believe this is correct for what I want to accomplish. according to markster@ this is the way they do it. using (multiple distro versions

I just got my Access Bank 2 (of course i'm happy now:)). Just need the wiring scheme Thanks

I've got a dedicated LD T1 terminating to a DMS100 switch. My outgoing calls aren't working, on the switch side they see two sets of dialing, with the first three digits repeating. I've used the sample extensions.conf modified a bit to remove the 9 and the 1, like so: [trunkld] exten => _NXXNXXXXXX,1,Monitor(wav,/tmp/dial) exten =>