similar to: Non working 800 numbers

I need a good reliable source for channel banks. Ebay is nice but too many variations of quality. I need one that can do 8 FXO and 16 FxS does anyone have a particular model, other than adtran that they can recommend??? And if possible include a source to buy from... Thanks in advance, Alex -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have Asterisk deliver all voice mail to users as email attachments. I found by accident that there is a limit of 99 messages in your INBOX in Asterisk. The 100th attempt to record a voice mail causes the system to play your greeting and then never record the 100th message and silently disconnect the caller. So...is it safe to simply use the UNIX find command to delete any files in the

We have had quite a bit of success with our T100P and TE410P cards interfacing to Nortel Meridian PBXes and also to a Livingston Portmaster 3 using ESF/B8ZS and various combinations of E&M wink and ISDN PRI (usually in 5ESS mode). In the near future, I may also need to interface to a Definity via a T1. I was planning to use PRI--is that an option for you on your switch? -----Original

I receive calls over a T1 with callerid and then *ani*dnis*. I am able to strip out the ani and the dnis in the dialplan but when I try to set the caller ID to be the ani, it looks ok but then if I do a NoOp callerid on the next line, I get unknown. Here is the section of my dialplan: exten => _*NXXNXXXXXX*NXXNXXXXXX*,1,Set(ANI=${EXTEN}) exten =>

Hi All, as good? I am trying to make a call for the Unicall channels and after the exchange of signalling and sending of the digits asterisk locks up with the sending of the signalling "E" and the TELCO says that asterisk would have to send signalling "F", as to make for asterisk to send signalling "F"? The TELCO says that the signalling "E" is

Hi, ? I run the program testcall with one E1, it works fine; I receive DNIS and ANI for making calls and answering calls. ? When I start the Asterisk I receive call from outside correctly including DNIS and ANI, and receive the following messages: ? Sep? 7 10:29:59 WARNING[12167]: Answer Call Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Call control(5) Sep? 7 10:29:59 WARNING[12167]: MFC/R2

Has anyone in the UK got ANI to work on an inbound call ? Using asterisk 1.4 trunk and zaptel 1.4 trunk, with a Euro-ISDN 30 Julian ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please visit http://www.messagelabs.com/email

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

Hello All, I'm having problems with international calling via Global Crossing. I'm told I need to send a true ani versus a sudo ani. What is the difference and how can I configure asterisk to do this. Global Crossing is denying calls with sudo anis. Thanks, Keith

Hi All, My research indicates ANI is not really supported with SIP Channels or passed between SIP servers, even with setting function CALLERID(ANI). So the only place this applies is on PRI interfaces, when sending calls out a ZAP PRI you can set the ANI to whatever and CID Number to a different whatever so on the other end of the PRI you will receive the two different values? Is this correct or

Hello, We're having some issues with CallerID and I thought someone here might be able to shed some light as none of our carriers seem to know what I'm talking about. The issues is this: A client of ours uses an after-hours voicemail service as mandated by their corporate office. We have a Day/Night setting that lets them turn this on and off. A call comes in from one of their

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

does anyone know how to route a call coming in with ANI*DNIS* Oct 31 12:47:41 VERBOSE[30056] logger.c: -- Executing Set("Zap/49-1", "DID=1231234*4812*") in new stack I tried making a route for _.*4812* but that matched everything rather then just the dnis i wanted.. any ideas? I would preferably like pass the callerid along to my extensions, but for now the important

Hello, Being totally fed up with the lack of quality and reliability from both VoicePulse and BroadVoice, We are switching to a direct IP connection to Global Crossing. We've installed a local point-to-point T1 into their CO, and they will give/take SIP g729a directly and act as the gateway for us. In setting up the inbound SIP service, they are asking the question, "In what format do

after updating to 1.3.1 it says to have no permission to play! What the heck!

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

I understand that most VoIP providers allow for 911 calling but that 911 service is not the same as that available to PSTN.

I want to distribute a random number to each of the first 100 callers to my IVR. This random number will be matched to their telephone number. Where in Asterisk can I do this? And, how? Logic. Call arrives. Context for announcement begins. You will receive a authentication code at the end of the message. Then, if they press a certain digit to confirm then I simply pass a code to them. These

I can't seem to hide and/or set my caller ID from *. I'm using a quite recent (three weeks or so) CVS with an E400P card. I have pridialplan=unknown in zapata.conf and I'm based in the UK. The relevant bit of pri debug looks like this (reformatted to fit 80 char width): > Calling Number (len= 4) [ Ext: 0 > TON: Unknown Number Type (0) >

OK I am going to do it again. Global Crossing is now sending ANI but it is not in the format I expected. Any one know of a way to get this data into two seperate variables? The first number is ANI and the second is DNIS so it is "*tendigits*tendigits* on one line like below. < Called Number (len=26) [ Ext: 1 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan