similar to: Asterisk

I finally got my incoming and outgoing to work on Broadvoice with a configuration file that is no where close to the one given by them. Here it Is (sip.conf). For others who have a working config could u please share so that I could compare. Thank You [broadvoice] type=friend username=[number] fromuser=[number] secret=[password] host=sip.broadvoice.com fromdomain=sip.broadvoice.com

HELP! Ok, so I have the following SIP.CONF: [general] context=default port=5060 bindaddr=10.1.1.200 externip = XX.XXX.XX.XX localnet=10.0.0.0/255.0.0.0 disallow=all allow=ulaw allow=g729 allow=g726 allow=alaw register => ##########@sip.broadvoice.com:XXXXXXXXX:##########@sip.broadvoice.com/1234 [sip.broadvoice.com] type=peer host=sip.broadvoice.com fromdomain=sip.broadvoice.com

I have configured asterisk with the AMP php configuration utility. I am able to make outgoing calls through broadvoice but incoming calls are sent to BV's Voicemail and never actually enter the IVR. When I show sip debug info through the asterisk prompt it actually reads the incoming call from BV but then issues a busy signal sending the call to BV's voicemail. I also modified

Hi, all. The asterisk setup is working fine, receiving calls via broadvoice "initially". ? When call comes in via broadvoice number, asterisk picks it up and routes correctly, as long as the call came in within ~2 min from the previous one. In other words, as long as a call comes in within ~2 min since the previous one, asterisk will answer the call. However, if the call comes in

I configured this once now I forgot what I did. Two Broadvoice accounts. Incoming is simple - just use the phone numbers. Outgoing: Dial out on a specific line and/or set up the groups and select the other "line" if the first one is busy? -- James Taylor MetroTel 3505 Summerihll Road Suite 11 Texarkana, Texas 75503 903-793-1956

So it was all working well and then suddenly I'm unable to get incoming calls from BV. Outgoing is fine. I'm using AAH. I have the following settings; register=9738281625@sip.broadvoice.com:PASSWORD-GOES-HERE:9738281625@sip.broadvoice.com/2208 [broadvoice] username=9738281625 user=phone type=peer secret=PASSWORD-GOES-HERE qualify=1000 port=5060 nat=yes insecure=very

I did a quick google search of the lists site and couldn't find a definitive answer, so if it's there, I apologize for asking again. Starting about noon yesterday, I am no longer able to send/receive calls via Broadvoice. When calling in, I get a fast busy, and when calling out I get the following error: -- Executing Dial("SIP/112-572a",

Hi, I can't make outgoing calls via Broadvoice. I have tried each and every configuration that was posted to list previously. I am able to receive incoming calls fine. I get the following in asterisk console: ===================================================== asterisk*CLI> show version Asterisk CVS-HEAD-03/10/05-22:51:28 built by vicky@asterisk on a i686 running Linux

Since Thursday evening my asterisk box has been failing to register with broadvoice. I haven't changed any of my config files in the last week. Can anyone suggest anything? Asterisk is reporting: *CLI> Aug 28 16:15:17 NOTICE[6150]: chan_sip.c:3914 sip_reg_timeout: Registration for '703XXXXXXX@147.135.8.129' timed out, trying again -- Got SIP response 404 "Not found"

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

I have tried everything to get BV working outbound. All worked fine until the BV change last week. I called BV and they changed me to sip gen with a new password. I stripped my Asterisk server to one phone on Zap/1 until I get this working. The same BV account works fine with a SPA-3000 so I don't suspect a firewall problem. Symptoms: Asterisk registers with BV Ok Incoming calls work

Asterisk seems to register just fine with BroadVoice (asterisk -r, and then sip show registry shows sip.broadvoice.com is "Registered") ...but when I try to call my broadvoice number (from a cell phone), it rings one single time and then says "The party you are trying to reach is not available to take your call." This doesn't seem to be an Asterisk message but seems to be

I just signed up for the BroadVoice service a few hours ago, but for the life of me I can't get any incoming voice. The incoming connection is fine as it rings my extension from outside, but I can't hear anyone talking. Outgoing voice is working fine though. I've been looking through the archives, but I haven't found a solution to the problem yet. I even tried another router

I understand there has been some issues sending DTMF tone through Broadvoice. Can some provide me with symptoms? --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.700 / Virus Database: 457 - Release Date: 6/6/2004

Hi all, I am trying to configure my Asterisk PBX to connect to a broadvoice account. I want incoming calls to go to the "s" extension and to ultimately have outbound calls routed through my broadvoice account(s). I cannot for the life of me get this to register correctly. I am currently receiving this message on the console: Failed to authenticate on Register to

Is anyone else experiencing 404 errors on outbound dial with Broadvoice? I've followed the instructions posted by Broadvoice to configure sip.conf, and inbound calling works fine. Every time I try to dial out, I get a 404 "Not Found" error. Here are the relevant sections from my configs. sip.conf: context=broadvoice-in register =>

*sigh* Ok, I have fought and fought with this. I have read all the FAQ's, I have scanned the list archives. I can receive calls on * from my Broadvoice acct, but I cannot place calls... I have the 'World Unlimited' plan, and like 5 area codes that are local to me in Dallas. Can anyone help me? here are my config files... - sip.conf - [general] context=default ;

Hello all, When I call the Broadvoice number all is good. When I try to call out through DISA on my broadvoice line i get the following: Executing Dial("SIP/147.135.0.129-0815bc60", "SIP/16037862111@proxy.bos.broadvoice.com|30") in new stack -- Called 16037862111@proxy.bos.broadvoice.com -- Got SIP response 480 "Temporarily Not Available" back from

Hello All, I'm just getting into *, and trying to use a Broadvoice account. It works inbound, but Outbound fails no matter what sip.conf parameters I try. From the recent posts here I think it could be: A bad CVS release - I will try to download and build from a new one Broadvoice not challenging and/or Asterisk not responding with an Authorization: in the INVITE header. I am

I have added the three lines to the sip.conf file based on the latest changes from broadvoice. I can receive incoming calls but cannot place any outgoing calls. The error I get is: *CLI> -- Registered to '69.73.19.178', who sees us as IPADDRESS:4569 -- Attempting call on SIP/Broadvoice/5068012 for application Playback(demo-congrats) (Retry 1) Mar 8 08:35:21 NOTICE[29290]: