similar to: chan_capi problem

Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hello All, I am having an odd problem with Armin's chan-capi_cm on builds higher than 7955. It would seem that this happens on anything higher than 7955. What is happening is the isdn is ringing, then asterisk does a goto-if and just hangs. Asterisk itself is ok, but the isdn then rings out or busys out on the other side. Outgoing works fine, this only seems to effect incoming. I

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

hi, I've been running a pure sip asterisk box for a while now with no problems, and i've recently added an isdn2e line from bt in the uk. everything is hooked up and i've got it ringing my sip extensions, but the logs don't quite look perfect and i can't see any description of what i should consider to be normal behaviour. would someone be able to look this over and tell me

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hello, These are error messages I get when I try to call a number over CAPI channel. -- Executing SetCallerID("SIP/xlite1-3b80", "0") in new stack -- Executing Dial("SIP/xlite1-3b80", "CAPI/hfcpci/b17") in new stack > data = hfcpci/b17 > capi request for interface 'hfcpci' == hfcpci: Call CAPI/hfcpci/b17-1 (pres=0x00,

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/bmp Size: 2918 bytes Desc: Picture (Metafile) Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050307/cb404791/attachment.bmp

Hello List, because this is my first post to this list, i'd like to introduce myself. My name is Thorsten M?ller, 26 years old and live near Frankfurt/Main in germany. Okay, now to the reason for this posting: I just installed my first asterisk server (Debian 2.2 Kernel 2.4.18-686) with AVM ISDN Fritz PCI card (passive). I followed the configuration on http://voip-info.org and the

Hi, I installed Asterisk with CAPI support. Everything works fine while starting Asterisk, but when a call comes in Asterisk hangsup the call after two times of ringing. The output is like: Jun 24 22:19:49 NOTICE[1082178480]: chan_capi.c:1931 capi_handle_msg: CONNECT_IND ID=002 #0x011d LEN=0048 Controller/PLCI/NCCI = 0x101 CIPValue = 0x10

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over ISDN/Capi but I don't succeed. My `capi.conf' is like show in many tutorial on the web. In `extensions.conf' I just added the following lines: [capi-in] exten =>

Hi, I've a Fritz card which was working fine, recently I changed hardware and my nightmare started. Now when I call someone through the chan_capi (0.3.5 or 0.4.0) it works fine but when I receive calls I always get hungup. Can someone please give some help? Here are the logs: *CLI> -- CONNECT_IND ID=001 #0x0000 LEN=0049 Controller/PLCI/NCCI = 0x101 CIPValue

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

[Something seems to have went wrong with my previous posting. It appears on the archive page in another thread. I did not receive anything myself. So I may give it another try:] Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hi, i use chan_capi 0.3.1 with asterisk (stable branch cvs) and 3 x c4 active ISDN card. From Controller 1 - 7 there are no problems making calls between asterisk and the pstn. But when i make calls from controller 8 - 12 i get on every controller (8 - 12) a segmentation fault in asterisk :( I tried different linux distributions (gentoo 2004.1, redhat 9.0 , suse 9.1) but same error.

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I try to get callers forwarded to by mobile phone when they dial a certain digit. In my extensions.conf I have defined the following: [279xxxx] exten => s,1,SetLanguage(de) exten => s,2,Wait,5 exten => s,3,BackGround(demo-congrats) exten => s,4,Goto(boksa,#,1) exten => 3,1,VoiceMail,u1 exten => 4,1,VoicemailMain exten =>

I've the following setup : sip phone -> ser (auth and routing) -> asterisk with capi isdn when I call a pstn number everything works fine, but I can't hear anything till the called answer. this is the output from a test call : -- Executing Playtones("SIP/2.7.184.61-08152880", "dial") in new stack -- Executing Dial("SIP/2.7.184.61-08152880",