similar to: Adtran 750 DID question.

Has anyone on the list been able to locate and try out the 1.1.0 firmware? It was released in November, but I have yet to get my hands on it. The Polycom site has way more docs online, but the link to the firmware only brings up the release notes. -sb

Caller*ID used to work as some point, but I can't seem to get it going these days. The card is a x101p. I've tried going up and down the rxgain scale. Can the txgain effect it at all? When I plug in a phone into the line with a splitter it can decode caller id with no problems. Reading through the mailing list archives hasn't given me any move clues. Any ideas?

I've been trying to get a Win 2000 RAS server working with my asterisk PBX for quite some time, to no avail. I've googled, I've tried loads of configurations, I've rewired phone lines, and still I am not winning the battle. Here's my config. PRI->T400P->Asterisk->T400P->Adtran 750(L36 Firmware)->RAS Server. I have 4 Zap channels signalled FXO_KS to the 750

Hello All, I am experiencing some intermittent problems with calls coming inbound on my DID trunk. I have 12 DIDs that come into an Adtran 750. From there T-1 to a port on T400P. The problem is that some calls that come in don't seem to bridge properly. Heres what happens. Call comes in on Trunk. Call Routed to correct Zap Channel. Phone Rings. Person Answers phone, but hears nothing but

Does anyone have any recommendations for overhead paging systems for use with Asterisk? Thanks, Randy Johnson -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031113/82ae09ec/attachment.htm

I just had the same exact problem this morning. The only thing I've done in the last couple of days is update update zaptel. I rolled back my zaptel to 2/11/04 from 3/8/04. And kept my libpri from 3/8/04. I never had this error before updated. I had other issues, but not this one. -sb -----Original Message----- From: asterisk-users-admin@lists.digium.com

To all Asterisk guru's... Here is my question. 1. Asterisk PBX - 5 Trunks / Incoming lines 2. 1 Building - 3 Companies (sharing phone system) Ok that's the basic layout. Here's the low down - Each company will have one dedicated channel for there company. The other 2 channels they want to be set aside as rollover's (rotary). That is not an issue. Where my concern is, how

Hello All, I'm having a weird problem when connecting up to a TA 750 from adtran. The problem I'm seeing is that the third wire on my 66 block is behaving as the tip (or ring) for every extension. Is this indicative of a bad BCU? The only extension that works properly is extension Zap 2. Every other extension is crossed with Zap 2. Very weird. Anyone see this before? Did I get a

Hello All, Quick question here on equipment selection. Is there any benefit to using a bunch of Adtran 850's with RCUs over 850s with BCU L1 to interface with the T400P. I'm looking at building a PBX with 7 channel banks. 6 x 24-port FXS and 1 x 24-port FXO. Would the RCU give me any advantage/functionality over the BCUL1? Thanks, Scott

All, One of our customers is using a Telrad PBX, we are providing phone server through asterisk via a T1 using e&m directly connected to the Telrad system. We're using a T1 cross cable as normal, the T1 part works great. No alarms. When we try and dial out the Telrad using a direct trunk group, the call fails. When looking in the asterisk console I noticed only 1 or 2 digits are seen,

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

I have an installation which is currenly using 14 DID Trunk Lines. I need to be able to use Caller ID information and currently it is not available on these lines. Is there another way to access this information? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040105/62559e22/attachment.htm

Ok, I'm about to take the plunge, and am trying to decide between Channelized T1 E&M and PRI. I'm getting an "Integrated T1" which will have data and voice capability, all plugged directly into my digium single T1 card. In either case the data piece looks pretty straighforward, just setup the channel properly, hand it off to the linux hdlc layer, and route away.... the

When people call into my * box over the T1 interface, they get no ring tone. It rings the SIP phone and when the SIP user picks up, both parties can hear each other ok, its just the PSTN user calling in hears no ring. What could be causing this? I tried setting immediate to yes in zapata.conf, but that causes my DNIS and CallerID to stop being available. T100P with E & M Wink start

does anyone know how to route a call coming in with ANI*DNIS* Oct 31 12:47:41 VERBOSE[30056] logger.c: -- Executing Set("Zap/49-1", "DID=1231234*4812*") in new stack I tried making a route for _.*4812* but that matched everything rather then just the dnis i wanted.. any ideas? I would preferably like pass the callerid along to my extensions, but for now the important

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the

Hi List, I need to change my provider, at this time Asterisk box is on VOIP trunk. I have two options, T1 or 15 analog lines. I have some experience with analog and I have had two main issues with it. first is echo (I have not tried HPEC yet) and second unpredictable volume. The question is, if I use TE100 with PRI , will I have same issues? I would appreciate any comments and sample zaptel.conf

I am sending a call down a E&M wink trunk to a adtran tsu600 channelbank. The extension is setup like so... exten=>799179,1,Dial(zap/g2,20,D(9179)) exten=>799179,2,Hangup() It should Dial the Adtran and send some DTMF signals to a telephone on an fxs module in the Adtran. Asterisk is seeing the call answered when the T-1 is picked up by the Adtran not when the ringing phone is answered.

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm