similar to: CAPI: Early-B3 working with AVM-B1?

Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and

Hi everybody, I have a problem which I cannot eliminate on my own. Has anybody any idea for the following: I am using the asterisk-version from Debian-Testing (1.2.13) with the latest chan_capi (also tried an older version). When using the Capi-Channel, everything works fine except from the sound it sounds extremely choppy and is unusable :-( When e.g. capisuite is used for fax, everything

I have a Diva Server BRI installed in a Debian system running Asterisk 1.2.22. When a call comes in the Background application plays a couple of times. Halfway through the second time, the call is disconnected (total time connected about 25 seconds). I've posted various configs below. Any advice on how to debug would be appreciated. We are located in New Zealand. CLI showing capi debug (just

Hello List, I'm trying to get a PrimuX Card (www.primuxisdn.de) working. The Manufacturer says that chan_capi (the older one) used to work. Now I'm trying with chan_capi-cm and have got the following problems: Outgoing calls "ausgehend_ueber_ntba_primux.txt" the other phone rings but when I answer the call asterisk crashes. Incoming: first tried with immediate=no

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a

Good day, The unusual thing about this problem is that it doesn't occur just during a CAPI call, or just during an IAX/SIP call. Only during IAX/CAPI I'm having some trouble with the CAPI interface and it only occurs when a call comes in on an IAX channel and goes out the CAPI interface. The capi debug in the asterisk console is below as well as the relevent parts of .conf files from

Hi, I've a Fritz card which was working fine, recently I changed hardware and my nightmare started. Now when I call someone through the chan_capi (0.3.5 or 0.4.0) it works fine but when I receive calls I always get hungup. Can someone please give some help? Here are the logs: *CLI> -- CONNECT_IND ID=001 #0x0000 LEN=0049 Controller/PLCI/NCCI = 0x101 CIPValue

I've the following setup : sip phone -> ser (auth and routing) -> asterisk with capi isdn when I call a pstn number everything works fine, but I can't hear anything till the called answer. this is the output from a test call : -- Executing Playtones("SIP/2.7.184.61-08152880", "dial") in new stack -- Executing Dial("SIP/2.7.184.61-08152880",

Hello, i have asterisk with chan_capi ( AVM Fritz card ) working, isdn line BRI, setup to point-to-multipoint. working fine, but when both channel on interfaces are used and somebody wants to call in - the response is "ha-la-li" - sounds like msn or called number does not exists. i think that right response should be - line busy tone... right ? can anybody tell me what is wrong ?

Hello List, because this is my first post to this list, i'd like to introduce myself. My name is Thorsten M?ller, 26 years old and live near Frankfurt/Main in germany. Okay, now to the reason for this posting: I just installed my first asterisk server (Debian 2.2 Kernel 2.4.18-686) with AVM ISDN Fritz PCI card (passive). I followed the configuration on http://voip-info.org and the

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

Hi; I've been asked to take a (remote) look at an Asterisk@home system running asterisk 1.0.9 on Centos 3.5. It's running chan_capi-0.3.5 It has an AVM c2 ISDN card which is plugged into what I believe to be a couple of BT ISDN2e "System Access" (i.e. point to point) connections. We've placed a support call to BT to find out how these lines are actually provisioned, but

Hi, I am having a problem with (Asterisk is crashing) with a Fritz card PCI / chan_capi. Receiving Calls from PSTN works, but outbound calls make asterisk crash (Speicherzugriffsfehler/Segmentation fault). The crash occurs upon dialing with the other phone not even ringing. I hereby ask if somebody reading this list can confirm or disprove my issue. Does anbody run a recent asterisk 2.6 with

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 i fixed wrong capi.conf (there was [controller1] after [interfaces]) now capi.conf is: ; ; CAPI config ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] msn=855285,859609 incomingmsn=* controller=1,2,3,4 softdtmf=0 accountcode= context=local ;echosquelch=1 ;echocancel=yes ;echotail=64 ;callgroup=1

Hi, Regarding capi debug, I don't know how to translate reasons like 0x3302 or infos like 0. I didn't find any 'translator' googleing capi debugging. Do you know about any 'translator' for this or should I be as clever as to know what a reason 0x3302 is? What is this debug for if I can't interpret it? Kind regards, Victor. >From capi debug: == CAPI Call

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hi, I have an AVM Fritz! ISDN card connected to an NT1 unit (Australian). I have no problems getting the drivers up and running but when using it with asterisk nothing happens. I call in using a mobile or analogue phone on either of the numbers and the NT1 activity light either flashes or goes solid while ringing but it pauses for a while and on a mobile i get call not answered and a busy

Hi, i was able to solve my problem. During my playing around with * and capi i changed several options in config files. I did this while my * was running. To test if my changes where successful i entered "reload" on * console. This didn't help. But after i stopped asterisk and startet it again, everything worked perfect. So it seems that doing a reload while asterisk is running

Hello, I need to detect both fax and answer machine, and it should be valuable that the detection will be run by the Diva card itself. So : - I read Diva Documentation, and I found that the Diva could send some specific DTMF, if I had "[..] enabled [this functionnality] by the application for a designated controller through a manufacturer request command 9 [...]", but I didn't

Hi, after having read so much about Asterisk, I went on and tried out to create a little sample-setup. I'm using a Fritz Card USB with the AVM Capi Driver and two X-Lite Softphones. Dialing between the softphones makes no problem. Calling the MSN fron an external phone also works. I'm getting to the asterisk demo-voicebox which works flawlessly. Now may next step has been to enable