similar to: drop calls with T100P / PRI

Hi, I'm seeing a problem when calling into my Asterisk server from a T100P with PRI signalling. I'm hoping someone has seen this as well, however, it's a little hard to explain. When I'm navigating through Asterisk on an inbound call from the PSTN, I'm getting a random 'noise' during the playback of sound files. The best way I can describe this noise, is imagining a

I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel bank (12fxs/12fxo). I have the setup partially working thanks to some help from IRC. However I still have the following issues I can't seem to resolve 1. When calling into the system from the PSTN call hangup is not detected. * leaves line in use until it is shutdown. 2. When calling an analog phone connected to

Hi all, inside my * is a E400P. The machine is a PII 400Mhz with 256MB Ram. OS is Debian woody. * is the newest cvs co. I have written a little callgen script which make outgoing calls through my *: #! /bin/sh set -e n=$1 # Nummer anz=$2 # Anzhal der Versuche anz2=$3 # Kan?le sle=$4 # Timeout bis zum n?chsten Versuch if [ -z $4 ]; then sle=0 fi s=1

I have been experiencing a rather odd issue with my (newly connected) T100P card. It is installed in my Asterisk server, which is working great with SIP clients. The card is connected to a channelized T-1 line (24 channels). The odd bit is that outgoing calls (Asterisk --> T-1 --> PSTN) works just fine. However, incoming calls (PSTN --> T-1 --> Asterisk) are dropped after about 20

Do they fall under FCC certification if they're built to the same specifications as the ones from Digium? If I build my own T100Ps from the schematics and board layouts that are available, are they legal to plug into the PSTN?

Hi Guys, I am getting a complain that call on analogue lines (Sangoam A400D) drops all of a sudden. Here is what I see in logs: [Jul 28 15:49:08] DEBUG[21438] dsp.c: ast_dsp_busydetect detected busy, avgtone: 75, avgsilence 135 [Jul 28 15:49:08] VERBOSE[21438] logger.c: -- Executing [h at macro-dialout-trunk:1] Macro("SIP/2111-b6a400b0", "hangupcall|") in new stack [Jul

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

I have a couple of X100P's in my system and while on calls they just randomly hang up for no reason. I have tried messing with the busydetect and callprogress setting them to yes and no same and still random hangups. Is there another setting I should be looking at? My zap config looks like. context = inbound-work include => extensions signalling

I've posted this problem a couple of times before with little or no response. Basically I have a T100P in my * box. Incoming calls are working great. However outgoing calls are not working at all. I've copied a previous post into this message which should have all the necessary info. Any ideas or suggestions would be greatly appreciated. Thanks. Mark

Ok I know I'm not the only one having echo problem with asterisk but the weird thing is that when I receive a call from a PSTN line on my TDM04B card I don't have any echo problem at the beginning of the call then after a few minutes I start having echo on my side only (the person calling from a regular phone doesn't have any echo), then it stop and come back all the way until the

Hi all, Our asterisk PBX, randomly restarts all the channels of the E1 connection. It sends this message "There is no D-Channel, using channel 16 anyway".Then the asteisk recive (or it thinks it recives) yellow alarms at all the B-channels, after that it restart all the channels. When restarting the B-channels it cut all the conversations that is handling at that moment. Does anyone

Ive just installed a TDM4000P with 4 fxos. The zaptel config is fine, zttest comes back with configured. If i call a line when zttest it shows on the display,and then goes when the line drops. In * when a call comes in, it follows my dialplan and answers the call according to the log, but IT DOESN'T actually pick up the call, i.e. it continues ringing. I'm using KS signalling, and

Hello! I am trying to install a TN405P on a P4-3GHz-HT machine running Debian Sarge with kernel 2.4.27. When I start Asterisk in -vvvvc mode it always shows == D-Channel on span 1 up == Restart on requested on entire span 1 == D-Channel on span 3 up == D-Channel on span 2 up == Restart on requested on entire span 3 == Restart on requested on entire span 2 == D-Channel on span 4 up == Restart

Hi List, I've got * randomly hanging up on inbound or outbound calls on zap channels. I use a Digitnetworks X100P clone card. Any idea of what might be happening? Cheers, Jean-Michel.

Hello, my config : aah 2.6 (asterisk 1.2.4) , centos 4.2, 1 TDM11B (1 Fxo / 1 fxs ), 1 phone, 1 softphone I'm in France When someone from PSTN calls and hangs up before the call is answered, internal extension keeps ringing until timeout occurs. PSTN line keeps busy. Hangup detection doesn't work. I've played with different paremeters (callprogress, busydetect, busycount,

Guys, this is weird.. Today I started having some problems with calls been dropped. Im suing X100p cards (clones) and I have this setting on my zatala fle: [channels] language=sp signalling=fxs_ks usecallerid=yes cidsignalling=bell cidstart=ring hidecallerid=no callwaiting=yes usecallingpres=yes ;sendcalleridafter=1 callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes

hello, We encountered signaling problem with a french national carrier. They ask us, which signaling is configured on our single E1. I need to know if it's ETSI, VN4 or VN6. I know what ccs, and hdb3 mean but I do not succeed to make the link between the signaling type. I searched through RFC Q.921 and Q.931 It would be great to obtain some help. cedric

Hi, I'm having random hangup problems with zap channels. If I turn busydetect off in Zapata.conf, * fails completely to detect a user hangup in the middle of a script. On the other hand, if I turn it on, everything works much better, but long calls tend to be hung up without a motive. Any other parameter that I can try? Any #define that I can tweak and recompile? Will callprogress

Dear All, I am trying to setup an ISDN line from local telco on a digium card. The problem I am facing is that I am not getting any caller id from the telco. They say that they have enabled caller id. Please help me out. My zapata.conf -------------------------------------------------------------------------------------------------------------------- [trunkgroups] [channels]

My PRI is being reset at least once a day with the following errors in the logs. zaptel, zapata, libpri, and asterisk are from CVS this morning.. This has been happening for weeks on all versions (including -stable). the T100P card appears to NOT be sharing an IRQ. xenon# cat /proc/interupts CPU0 0: 1203977 XT-PIC timer 1: 3 XT-PIC keyboard 2: