similar to: T100P positional on PCI bus?

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello All, I have had a problem detecting the network card on my notebook when ACPI is enabled for a year. The problem still exists in 7.1-RELEASE. with ACPI: ... bge0: <Broadcom NetLink Gigabit Ethernet Controller, ASIC rev. 0xb002> irq 17 at device 0.0 on pci8 bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). bge0: couldn't

Below you will find, what I believe to be a typical setup with a T100P card. My question is - 1. Is this correct? 2. What kind of phones would be needed here... (Would you have to use Digital phones) And if so what would you recommend. PRI/T1----- | | | ---------------- | | | Channel Bank | | |

I have a pri comming into a t100p in my asterisk box. I have a second t100p configured as pri_net connected to a nas server. I can route modem calls to the NAS with no problem, but I am concerned about isdn data connections. Will asterisk route 64k isdn calls between 2 t100p's? Also, should I expect worse modem connections than normal? Chad Sawyer -------------- next part --------------

I'm experiencing similar problems with a 3C996-T under 4.8-REL. In particular, connecting a 4.8-REL machine to a 5.1-REL machine leads to some interesting situations: I can do simple pings across the link, but ssh fails, and heavy pings crash the 4.8 machine. Similarly changing the interface configuration with ifconfig tends to crash the 4.8 machine (mtu, link0, up/down, etc). The

I would also like to help as well. As KMacy knows before i asked a lot of questions for T2 types of servers but unfortunately i have no more access to those kind of hardware as well. I;m willing to participate if a team will be formated.

Dear Sirs. It seems to me a never ending story. We run a box with a TYAN Thunder 2500 Dual SMP mainboard, 2GB ECC Tyan certified memory, AMI Enterprise 1600 RAID adapter and additional Intel 1000/Pro server type (64 bit) GBit LAN NIC. With FreeBSD 4.8 this was stable, but to achive this state was really hard! It is a story similar to that what happend when we changed towards FreeBSD

Hello, Does anybody know of a place to get a half-height PCI slot bracket for the Digium T100P card? I have an application to fit them in 1U cases for small, deployable PBX's. The T100P itself is short enough to fit in a half-height slot but I need an appropriate mounting bracket to screw it into the case. Thanks, Mark Hagler

Hi List, After reading a bunch of the docs, list post archives, it still seems that a clear definition of how to clock the T100P card is muddy. zttool says that the link is "INTERNALLY CLOCKED", does this mean the T100P is providing clock, or does this mean the T100P is getting clock from the T1 line side (ergo getting clock from the Telco) ?? If you have sync = 0 then zttool

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

anyone have a recommendation for a place I can buy cheap motherboards that supports those 64-bit 3.3 volt PCI slots for the T100P ? I can't find them at Fry's or anywhere locally. All I can find online is dual processor server boards that are overkill for this application. I would like to use a P3/ P4/ AMD single processor. No Xeons or dual processor junk. Anyone know why digium

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed

Management just approved purchase of a Digium T100P and a T1 card for our Merlin Legend Switch. I will appreciate comments from anyone performing this installation before: - Which T1 card did you use in the Merlin Legend? - Did you require any special interface? (CSU/DSU, etc) - Any items to watch during installation. Also we will need to remove one of our old analog Trunk cards to accomodate

Hi, I have a server (Dell PowerEdge SC1435, ServerWorks HT1000) on which I'd like to try installing FreeBSD. I've already failed to make 7.0 work on this box and was wondering if you have information about the behavior of the upcoming 7.1 on this hardware. I've been following the "HT1000 chipset errata saga" thread, and the commits by sos@ to CVS (around Jan 2008), but have

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.4 - Release Date: 12/22/2004

Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31

Hello all. I have a supermicro 16 bay box with a LSI 9211-8i card. We use it for temp data storage, and we wanted to try the l4z compression. After updating the source tree to r247839: and doing a make buildworld cycle all works fine. But at boot time we get some warnings. make_dev_physpath_alias: WARNING - Unable to alias gptid/281951f4-a996-11e1-83eb-00259061b51a to enc at

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

Hello, So all the pieces are finally here, and I'm ready to play. I remember reading on this list that the connection Channel Bank <-> T100P requires a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only a couple of pairs reversed?) Please help me before I blow something up! Saludos, Jose.

I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type