similar to: grand stream phone and double nat

Hi All I'm having problems posting to this list, no bounces the mails just dont show any advice how to get the postings through is there filtering? robb

Hi I have looked through the wiki and search the mailing list, but I cannot find a way to intrude on a call, can asterisk do this feature? if so how? Thanks for your help Robb

Hi All I cannot seem to find a way to stop atserisk inercepting DTMF tones and regenerating them even on a zap to zap bridged call is this possible? Thanks Robb

Hi, can anyone recommend a Linux based TFTP server to go on an asterisk box? Thanks in advance Robb

Hi I have a requirement to bridge Digital ISDN call through an asterisk box but no matter what I setup in the dial plan the second leg of the zap bridge is always set to Transfer Capability of SPEECH, I wondered if any one has come across this and managed to fix it? Thanks in advance for your help Robb

Hi List I'm trying to update to the lastest kernel but I have a dirver that is not inculded in the distrubution, and I had to use the driver disk when installing centos 4.4 in the first place, The driver megasr .ko works fine with the installed kernel but I cannot find on for the updated kernel, any adive would be appreciated. without the updated driver there is a kernel panic on boot due to

Hey all, I was playing around with IAXTEL last nite and have outgoing calls working a treat. I'm sure I woke a few people up in the US with my annoying test calls. :) Anywayz, incoming calls are a different matter. I have a NAT firewall my * box is sitting behind and the server 'appears' to have registered correctly with IAXTEL. Thing is, when I try and call my 1700 number

Hi I have a problem with a new DECT phone I have bought The key pad works like a Mobile phone where you dial first then pick up the line, but it seems to dail too fast or spuriously, ie 012826736464 show on thew Asterisk console as 0012282677, could any one offer advice how to fix? Also when doing a ZAP bridge to this phone from an outside line the call is very echoy, but not an internal

Hi I have had a Centos 5 installed with asterisk and zaptel for a couple of weeks, I had to reboot eh machine today, and when it rebooted it got stuck at "Starting udev" if I remove thew tdm400 it boots OK, but no zaptel has anyone seen this , and can offer any advice? Thanks Robb

Robb, I wrote up a small tutorial on setting up the standard tftp server for linux check it out on my site. http://asterisk.titaniumsoft.net/ Mitchel -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Robert Boardman Sent: Thursday, May 13, 2004 2:44 PM To: asterisk-users@lists.digium.com Subject:

Hi All Just been looking at stats for one of my sites, and I'm conserned about the number of error cause codes being returned from the telco for example 12000 calls processed 131 are cause code 31* normal. unspecified.* 139 are cause code 28 * invalid number format (address incomplete).* 112 are cause code 1 *Unallocated (unassigned) number. *this adds up to about 3% of calls not

Hi I'm having a problem where the recall button doesn't work If i press recall before I dial numbers it disconnects me which is what I would expect, but during a conversation if I want to transfer the TDM 400 just ignores the recall Any advice would be gratefully received Thanks Robb

I have two questions about incomming ring and extension ringing 1) When an incoming call is detected by asterisk it takes 2 or three rings before the internal phone ring does anyone know how I can fix this? 2) All internal phone ring on an incoming pstn call but after the call is answer all the other phone ring for a couple of tinkles how can I stop this from happening? Thanks for your

Nearly got an SPA922 phone working behind a NAT, the phone registers, and I can dial out and have two way speech, on an incoming call the SPA922 rings I answer and the SPA922 shows "Anwsering" but never does and the far end continues ringing until the voicemail answers, this then show as a disconnected call on the SPA922 I'm on the lastest firmware 6.1.5(a) Thanks in advance

Hi all I ahve been having problems loading the wcfss and wcfxo drivers I get an error message invalid argument and something about post install insmod failed the currently load modules do show the drivers loaded but asteris won't start lsmod root@slackware:~# lsmod Module Size Used by Not tainted soundcore 3332 0 (autoclean) wcfxo

Could someone point me in the right direction for setting up the mysql cdr function Thanks robb

Here is just one example of a warning when compiling asterisk on Ubuntu 8.10 manager.c:1760: warning: ignoring return value of ?read?, declared with attribute warn_unused_result is this anything to worry about? can i safely ignore it? Thanks Robb

Hi All I would Like to run a macro in a meetme conference when a user presses a certain digit sequence, but I cannot seem to find how to do this , is it possible? if so how? Thanks for you help Robb -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20091119/9ff3f816/attachment.htm

Help, I'm stuck. Lost in the woods. I have one Asterisk running on FreeBSD outside on the Wild Internet. One on the safe inside, behind a NAT firewall. The inside server registers with IAX to the outer one and can place calls. The outside one can't register to the one on the inside, since it can't be reached on the private network. Now to my problem: * How do I dial from outside to

Hi all, I'm confused as to where I need to place the Asterisk server with repect to my Linux Firewall? I've read thru the message archives but have not been able to glean a clear answer. My Linux Firewall is a RH9 running IPTABLES doing NAT. Here are my questions: 1) I want to be able to make and receive SIP and IAX calls(From sources like FWD, IAXtel, iptel etc.). I read in one