similar to: what is ztcfg for

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

Hi All, Just installed our very first asterisk system, and we love it! I cant believe the different things you can do with it, just great =] My question is: How do I configure my system to play an mp3 file when a caller gets put on hold? Thanks in advance, Steve.

Hello. I have been going thru the wiki and asterisk related sites and have not been able to find any documentation about how to configure an Adtran TA750 channel bank. The remote disconnect supervision doesn't seem to be working, when the remote caller hangs up asterisk takes up to 30-45 seconds to hangup the call. Can somebody help? Thank's

Anyone can share me with Music Onhold Configuration sample? Thanks in advance for your help, Kang

I am wandering if anyone can explain this unusual scenario. I am running Asterisk on Fedora. After the box boots, I run insmod wcfxs at a command line. The phones keep the red message light on and are in a state like they are not recognized yet. If I then run the command ztcfg, I don't get anything after the command, meaning that everything should be OK in zapata and zaptel confs and the

Hi All; In dahdi: what we use instead of ztcfg -vv (that is existed /sbin/ztcfg -vv). ? Regards Bilal

Hi all, I'm installing two HFC pci card (both in TE mode), I don't have problem when load module, but whrn I give "ztcfg -vv", I see 6 the six channels that I configured, then my computer hang and I have to reboot it. (I'm using a VIA Epia-M 1000 with Via C3 processor) root@test:~# modprobe zaptel root@test:~# insmod /usr/src/bristuff-0.2.0-RC8n/zaphfc/./zaphfc.o

Hello. I have this issue, when I pickup a call that is ringing in a SIP Phone, it keeps ringing. There is bug #116 that mention something about these, but it does not seem to be resolved , at least, not yet. Anybody else has seen it behavior ? Thank's.

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

I have a new asterisk system with a T1 card. It appears that running "ztcfg -vv " is required in order for asterisk to start properly. Is this correct? Are people adding this command to the asterisk startup script? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL:

I was wondering if anyone had experienced the following with asterisk stable. After a period of time (can vary), If I stop asterisk and try to run ztcfg -v to reinitialise my quad e1 card, the server will lock up. Sometimes it's a complete lockup, where it won't even return pings, other times it seems to be "partially screwed". -- ==========================================

Hello, I'm running Fedora Core 3 with udev, and asterisk/zaptel/libpri from cvs. I have followed the README.udev instructions replacing insmod with modprobe and rmmod with modprobe -r and adding the 60-zaptel.rules file, yet no matter what I do I still get this error on boot(or when I run service zaptel restart): [root@pbx ~]# /etc/init.d/zaptel restart Unloading zaptel hardware drivers:

Hi All, I just installed Asterisk 1.0.5, and the installation went fine (I ran modprobe zaptel and modprobe wcfxo). However, when I ran ztcfg I get the following: ioctl(ZT_LOADZONE) failed: Invalid argument Notice: Configuration file is /etc/zaptel.conf line 135: Unable to register tone zone 'us' After that I ran Asterisk and it seem to started ok, except that it won't pick up

I'm using two Rhino channel banks (first 12FXO/12FXS, second 24FXS). These connect to a Digium TE210P card. I'm running kernel 2.6.10 and I've tried Asterisk (w/zaptel) 1.0.9, 1.2 beta, and CVS from today. The results are the same for all versions: Right after I reboot, and modprobe wct4xxp, my analog phone connected to port 13 of the first channel bank (first FXS port) gets a dial

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

I am running * in a development environment, adding functionality as I go. The * box has a X100P card in it which ztcfg enabled as channel 1 with fxsks signalling (fxsks=1). Everything worked fine and I was able to make inbound and outbound calls to/from the PSTN, the only issue being that some exchanges wouldn't handle the dtmf signalling, but I put that down to a peculiarity with some AU

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

Another nibbage question: modprobe tor2 -v install /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg insmod /lib/modules/2.6.5-1.358smp/misc/tor2.ko ZT_SPANCONFIG failed on span 1: No such device or address (6) FATAL: Error running install command for tor2 dmesg states that the module is registered however. Am I doing something seriously wrong? I have my zaptel.conf configured as