similar to: SIPURA Breaches Contract

I am trying to get the following phones for testing. Is there a distributor in the US that is able to sell me these Sip phone and ATA adapters? I can not afford the Cisco phones there too hard to configure and too expensive! 1 - Sipura SPA-2000 2 - Grandstream Sip phone BT-102 1 - Grandstream HT-286 1 - Snom 105 Sip phone. I have called and emailed chagres but they have not reply. Nor

I am trying to configure the FXO port on a Sipura-3000 for use with Asterisk. When I connect to the Sipura to dial out on the PSTN line connected to the Sipura's FXO port, it gives me the dialtone of the PSTN line and then I can hear the DTMF for the number I dialled beforehand. It does work but the customer perceives this delayed second DTMF feedback as "unprofessional" and the

Does anyone have a Sipura 3k running, and using the FXO? I've got things working right, but if I try to toss a *67 in the dialplan, it seems the sipura is throwing a 403 forbidden back. For example: exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/${EXTEN:1} works fine exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/*67${EXTEN:1} does not (even if I toss a couple Ws in) I can't

Anyone have experience with Sipura's? Anyone know if they offer a warranty? Would like opinions on these, good or flame. We bought *one* to test with and it died, can't even get a response from Sipura "support". Could anyone recommend another device to replace these? Prefer 1 or 2 port design. Ty :-)

If I understand correctly the Sipura people are the same guys that made the Cisco ATA (Komodo phone) or what ever. I'm going to get one of the Sipura SPA-2000 to use and abuse with *.... I have seen the web interface.. John over at Chagres was nice enough to let me login to one and look around a few weeks back... I'm impressed .. if you guys care to buy one

Hi there everyone! I've bought a Sipura SPA 3000, and succesfully connected it to my Mac, where I installed Asterisk 1.4.0. Both ports (FXO and FXS) are well configured). However, living in Brazil, I'd like to know if there are optimal settings to my PSTN that I should enter into the config of the device. I experience a little bit of echo on the FXO probably because I raised the gain of

This question isn't entirely Asterisk related, but I'm hoping that someone here may have the knowledge to respond to me anyway. I'm using Asterisk with several Sipura SPA-2000 SIP devices as FXS adapters. I would like to have my SPA's automatically provisioned through http or tftp, but I can't find any information on how to do so. Sipura's tech-support has not been very

Anyone have any luck RMAing a Sipura phone since the Cisco take over? Sipura only has support via email or fax to end users and I haven't gotten a response to either for over 2 months. Linksys Support will jump you through all their scripted hoops to resolve your problem (they hope if they speak with a thick enough accent and make repeat the same steps over and over again that you will just

Hello list, I have several SPA-2000's and 3000's scattered about the Internet (all behind NATs). Because I do not qualify as an ITSP, Sipura will not license their "Sipura Profile Compiler" so that I can have the units remote upgrade, remote re-configure, etc (via TFTP or HTTP). This is extremely annoying. Right now if I have to make a config change to any of these

Sorry to everyone on the list, but for some reason this is the only reliable way to get hold of John. John Brown of Chagres Technologies, please contact me! I have been trying for weeks now to get hold of you via email and phone after wire transfering money into your account for the Grandstream phones we ordered, but so far I have not had a single response, nor have the phones arrived! Please

I know the subject of faxing has been covered in some detail, but I was wondering if anyone has a hardware configuration similar to ours that has faxes working successfully and would be willing to share any settings/insight. We are unable to fax reliably with a Sipura 2100 connected to Asterisk. We do not route calls over the Internet and our network has very low latency. The Asterisk

Hello, How good is :SPA 841 form SIPURA. Thanks Varun

So what do people think about adding the "call rate" to the CDR structure?? This would allow you to detail a call with the rate that was in affect for that call. When you come back later and do the billing for the customer you would have the actual per min rate in the record. I think this solves an issue when you have changing rates and multiple providers. If one provider is down,

To All, I recently purchased a Sipura 3000 for home use. Generally it seems to work fine, but it also majorly screws up on a frequent, almost daily, basis. Terrible echo problems that come and go, and sometimes it just seems to "lose its way" and can't re-register. For example, I'll be talking to an incoming caller and an echo starts quietly in the background. Within a minute

Hi, I've had a bunch of people asking about purchasing GS phones. I'm happy to announce that we now have an online purchase system available. We have: BT-101 BT-102 HT-286 Plus the full line of Digium hardware. We will be adding other products in the near future so check back :) Buyers are responsible for s/h costs. The URL for the phones is:

Hi, I'm trying to configure Sipura 2000 (behind NAT) which connects to Asterisk (public IP, no NAT) and having interesting results. When Sipura is behind Linux/NAT firewall it works great and no special NAT settings on Sipura are necessary. The issue I'm having is when Sipura is behind Linksys broadband NAT router. Sipura gets registered with Asterisk just fine, but I can't hear

I have been trying to read everything I can find on Sipura 2000 and Asterisk. I am trying to make the Sipura-2000 act as two analog lines off my asterisk. I have followed (what I believe) the example on http://www.voxilla.com/Article39.phtml and I still can't get my Sipura to register with my Asterisk server. I can re-config my Sipura to talk to fwd, or voice-pulse connect and it works

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

As I've said several times on this list[insert usual apology here], I still haven't received the last 20 of 100 phones I ordered over 2 months ago. If you get a hold of them please let me know MATT--- -----Original Message----- From: mikeu [mailto:mikeu@execpc.com] Sent: Saturday, January 10, 2004 12:41 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Chagres

This may not be the right place to ask, but I have an annoying issue with a Sipura/SPA1000-2.0.10(e) ATA device connected to an Asterisk box. (The system is remote to me, so I've only been able to observe this by dialling into a VoIP phone on-site, then run commands on the box remotely!) First of all it's all working fine connected to an Asterisk box and the user can make/take calls