similar to: Dlink DG-104SH

I am have trouble getting caller id to work here is my current mgcp.conf am I missing something? ========================================================= Mgcp.conf [general] port=2427 [Egraph-1] ;dlink 104s-1 host = 12.151.207.2 context = local line => aaln/1 callerid = "jim's office 1" <321> line => aaln/2 callerid = "jim's office 2" <322>

What I am trying to do is in the 3rd option dial my cell# thru voicepulse I just can't figure how to construct the line [inevans] exten => s,1,setcallerid(${CALLERID}) exten => s,2,Dial(MGCP/aaln/1@Egraph-1,10,tr) exten => s,3,Dial(iax2/passwod@voicepulse.com/ Where do I put the # to dial 18708573287 thanks James Schenck Egraph Design Inc. Arkansas Online Internet Services (870)

Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to

Hi, For MGCP users. Is there any success stories with any MGCP IAD vendor. I?m trying to find an IAD which works with Asterisk. I?ve tried the Cisco IAD 2430 without success; but SIP on this IAD works but it?s limited (no authentication, no notify messages, etc) and with higher density IAD (16 or more ports) it?s nice to control using MGCP. Any information will be apreciated ! Thanks. --

I have a DG-104S (which I reset to factory settings, it's DHCP'ing off my network, plugged into the WAN port). The system comes up, and I through the web browser set under Call Agent IP Address to: Notify Entry: dlinkgw@[192.168.1.1]:2427 (192.168.1.1 is the * server) I have RGW Name: and DNS IP addres the DNS IP of the MGCP box and DNS State disabled (not sure what to set it to) --

Hello, is there a way to disable call waiting in sip? I`m using grandstream 101 and even when the phone is in use I hear ringing in the headset. It is pretty annoying , is there some way to disable this? I cant find anything like it in the grandstream docs. Thanks -- Anton Yurchenko<phila@dg.net.ua> Digital Generation

hello, I have a test setup with 2 asterisk servers, each having a one snom 100 via sip using it. I`m experimenting on how trunking between them would work. I have them setup for RSA authentication which I plan to use in the future. So I`ve setup the keys and servers seem authenticate to each other. One is named phila and other hurricane. Here is what I see on phila: -- Registered

Hello, Right now I have app queue working with incominglimit=1, there is no call waiting signal, but after a while( like couple of hours) some phones randomly get stuck. The * thinks that they are in use and doesnt ring them, when they are infact not in use. sip show inuse, shows that they are inuse. typing reload on the console resets this and they are again available for working. anybody

When I have an ip hardphone username setup in my sip.conf : [109] type=friend username=ipphone9 secret=bla-la host=dynamic dtmfmode=rfc2833 ; Choices are inband, rfc2833, or info defaultip=172.20.0.139 mailbox=109 ; Mailbox for message waiting indicator callerid=ipphone9 <109> callgroup=1 pickupgroup=1 and this user has a wrong password then calls are denied, but

Hello, I`m trying to make a call from the snom 100( SIP mode) but whatever number I dial I get a 404 error from Asterisk. Here are my configs and a dump from "sip debug" . But if I make a call from a Zap line (see extension 2382031), it rings the snom phone sip.conf: ------------------------------------------------------------------------------ ; ; SIP Configuration for Asterisk

Hi, After spending some time trying to get a DG-104S working behind NAT, I finally found the problem. I made the incorrect assumption that nat=yes in mgcp.conf works just like sip.conf. The channels within a gateway are treated more closely to zap channels than sip channels (from a .conf standpoint). What this means is that you have to put nat=yes BEFORE any subchannel definitions: This

I have been reading asterisks and everything I can get my hands on for the past week. I want to know what class processor is the bare minimum I need for a four port Asterisk installation? Thanks

Hello, I've successfully installed Asterisk from last CVS and configured it for using with DLINK-DG104S as mgcp CPE and PGW2200 as external sip server. All are work fine at G711 codecs, but then I disable all codecs except g729 some calls failed (Not all calls. Some calls passed at g729 succesfully). All my devices configred to use only g729 and I don't see other codecs at mgcp or sip

I just downloaded the cvs version CVS-07/28/03-14:45:19 and now I cannot recieve the the calls from the zaptel interface which is a E100P with pri signaling. That is something with asterisk becouse rolling back to version from 06/23/03 using the new libpri and zaptel fixes the problem. Here is an exept from the config: [macro-stdexten]; ; ; Standard extension macro: ; ${ARG1} - Extension

I write the email again, the third time!!, cause the other two ones, I have had problems while sending them. I hope this time it works. Here is the email again: Hi (and sorry) everybody I'm starting with SIP and I wanted to ask some questions, perhaps silly ones, but I hope people can answer me! 1) Which codecs may I use? I want the SIP phones to call to the PSTN above all, but I have

Hello, Anyone aware of any CRM products projects that intagrete with *? Or that integrate with any telephony products? Is there some open API for such integration, or are they all proprietory? Thanks -- Anton Yurchenko<phila@dg.net.ua> Digital Generation

Hello, Has anybody been able to get the Mute button work on grandstream? it simply does nothing. Only Hold is avalable, which is not that good. Thanks -- Anton Yurchenko<phila@dg.net.ua> Digital Generation

Does anyone know if this unit works with Asterisk? Thx. B.

I am installing a used DG104S.... I got it to ring from gnophone, but all I got was fast busies. so I upgraded based on Pavel's link: ftp://ftp.dlink.ru/pub/VoIP/DG-104S/Firmware/MGCPDG104.zip So I now have: PROM Version: 3.0B22-D RUNTIME Version: 3.0B44-D But when I pick the phone up I get: ggdbg>000001604 DIM: 0 DSP ERROR: Reason= DIM ERROR: State Timeout 000001604 DIM:

Hi, I'm using D-Link DG-104SH (H323 4 port FXS gateway) with analig phone connected to it and X-Lite softphone as endpoints with * When I calling from X-Lite to analog phone it's ok When I dilaling X-Lite from analog phone, X-Lite si ringind but whei I picked up X-Lite connection drops IP of DG-104SH is 192.168.1.3, H323 ID is GW1 X-Lite number is 233 Here is * output: -- Executing