similar to: COnfiguring an * system for a non-profit organization

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

Hello, Did anybody successfully tried upgrade Adtran TSU 600 to firmware which is working properly with T100P and asterisk ? B.

Hello, I have been researching Echo Can's for a while now, and wanted to post this out to the list to solicit feedback (and if my assumptions are correct, hopefully help others out)... If anyone out there knows anything about wiring up an Echo Can, and my outline below is incorrect, please let the me/list know.. I have posted the Documents I received from Tellabs at:

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel bank (12fxs/12fxo). I have the setup partially working thanks to some help from IRC. However I still have the following issues I can't seem to resolve 1. When calling into the system from the PSTN call hangup is not detected. * leaves line in use until it is shutdown. 2. When calling an analog phone connected to

I have a T100P card connected to an Adtran and then a T1. I have added the following configurations to Asterisk...but, when I dial 9 and then a local phone number, it bounces between the dial tone and silence and the *error* light on the Adtran blinks. zaptel.conf span=1,0,0,esf,b8zs fxsks=1-8 loadzone=us defaultzone=us zapata.conf [channels] context=from-sip signalling=fxs_ks

Hi, The PBX at the Colorado Organization for Victims' Assistance fried as a result of the building power being cycled. I'm now in the process of building an * system to replace the failed PBX. Minimum cost is the priority. I have a T100P card installed in the new system, and I am about to order integrated T1 services from the "CBeyond" company. They will require eight

We have been experiencing static noise on one of our phone lines connected to our Adtran Total Access 750 which is then connected to a T100P card. I was convinced that, after rain storms, the static would get worse, it was surely a problem of Verizon's. Verizon sent a field rep out today and he told our secretary (I was busy) that there was a hard ground on the Ring portion of the line.

I've been working with an adtran ta 850 hooked to a t100p pretty much all day today, and I haven't gotten past configuring zaptel.conf and zapata.conf. For some reason, when I pick up analog phone hooked up to the first module of a quad fxs card in the second slot of the ta 850, asterisk thinks that all four of the fxs modules in that card are going off hook. If I pick up a phone hooked

I have just received a T100P and an Adtran TSU 600 in the mail. I seem to be having a problem with the T100P card. So far I have done the following: vi zaptel.conf fxoks=1-22 fxsks=23-24 ... vi zapata.conf ... signalling=fxo_ks ... channel => 1-22 ... signalling=fxs_ks ... channel => 23-24 I then run modprobe zaptel modprobe wct1xxp ztcfg -vv There are no errors to report. In

Can I configure an Adtran channel bank with a mixture of FXS and FXO cards and have them come into a single T100P T1 card? It seems like this would be a cheaper solution than trying to load a bunch of PCI cards into a PC. Also, when shopping for an Adtran (on ebay) - what do I need to watch out for as far as interfaces or capabilities to make sure that it works with a Digium card?

All, Thanks for taking time to read. I am wanting someone to tell me that I have a clue here and that the following proposed setup would (possibly) work. Currently existing are 4 pots lines with qty. 10 AT&T 954/854 phones. Would like to convert to asterisk and at the same time do a mild feature upgrade. Proposing to get: PIII 800MHz or better >=256MB RAM

My carrier tells me our Adtran is seeing error seconds and timing slips. Is there any way to check this on the T100P, maybe in /proc? Craig Bruenderman Network Advocates, Inc. 300 Envoy Circle Suite 300 Louisville, KY 40299 Main: 502-412-1050 DID: 502-992-5929 Fax: 502-412-1058 Mobile: 502-548-1100

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

Can anyone share any advice / documentation on how to configure a Tellabs 2572 T1 echo canceller? I connected one between a T100P and an Adtran TA750 FXO/FXS channelbank, but when echo cancellation is active I get a LOT of snap-crackle-pop (and other problems) on the line. The 2572 has a bunch of configuration options and they're impossible to guess without documentation, which I cannot find

I am connecting a t100p to a b8zs, superframe, loopstart t1. Previously I've attached to e&m wink and pri lines with no problems; however I seem to be missing something. Should it be fxols in the zaptel.conf (smartjack to x100p) or fxsls? With e&m wink the dnis set was 100, so it was easy to make an extension 100; and it would answer incoming calls. How do you get a loopstart to

Ok, the Zhone sucks and the Adtran 750/850 seems to be a little too expensive. Can anyone recommend a decent channelbank that won't break the bank? TIA, -- Troy Settle Pulaski Networks http://www.psknet.com 540.994.4254 ~ 866.477.5638 Pulaski Chamber 2002 Small Business Of The Year