similar to: Cisco IAD with MGCP

Hi, Anybody out there running Adit600s? I have in my care an Adit600 channel bank connected to an old (version 1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk (1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail. I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It seemed to be the only likely candidate in the example files I found

I've never set up an mgcp device before. I have an Adtran IAD with the MGCP firmware on it. I have it configured in mgcp.conf like this: [general] port = 2427 bindaddr = 0.0.0.0 [adtran] host = 192.168.2.2 context = default canreinvite = no line => aaln/1 line => aaln/2 The device is configured like this: MGCP Configuration | Standard MGCP 0.1 / NCS 1.0 MGCP Endpoint

Hi, For MGCP users. Is there any success stories with any MGCP IAD vendor. I?m trying to find an IAD which works with Asterisk. I?ve tried the Cisco IAD 2430 without success; but SIP on this IAD works but it?s limited (no authentication, no notify messages, etc) and with higher density IAD (16 or more ports) it?s nice to control using MGCP. Any information will be apreciated ! Thanks. --

I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10.0.1.19-1 in cxmode: sendrecv Posting Request: RQNT 306

Hello, I have a cisco ATA 188 registering both of its lines to * I can place calls between then an to kphone an MSN messenger (both registering with * too), a few days ago a friend lend me a Cisco IAD 2430 and I was willing to do the same thing with it, since it has 24 ports I was willing to to use 24 analog phones with it however something really weird happens I can place calls from my ata,

Hey guys, can you shead some light on this? I will copy my mgcp.conf and post below, but here is the problem. I can't get call waiting to work with my MGCP device. I already have one call going, and I can hear the second call come in, I flash over to it, but all I get is a dial tone, * puts the 1st call on mute/hold, but I never get the second, and it terminates. I flash back over and pick

Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to

Hello I have a problem with my MGCP voice gateway. I use D-Link DG104S Boot PROM Version 3.0B38-D Firmware Version 3.0T86-D I tried asterisk v 0.7.2 and I am using latest CVS version now. When I dial a number very fast, or when I use a redial function, my asterisk receives coupled digits. My co-worker called number 245005111, these are a few lines of my debug. The identifier of first digit

Can anyone tell me what MGCP error that I'm getting means? The hardware is a MRP200 in a Cisco 7750 PBX. (Its a FXO blade with 2 slots, first one has a 4 port FXO card and the second has 2 port FXO card. It recognises those correctly, at least to the point of this error.) MGCP Debugging Enabled MGCP read: NTFY 13 aaln/S0/SU0/0@MRP200-S1 MGCP 0.1 X: 1adace42 O: L/hd from

> Hello all, > Can someone help me on the problem which I have on MGCP phone test . I test mgcp - asterisk- zap. But I got several NOTICE message from rtp.c. > NOTICE[20501]: File rtp.c, Line 221 (process_rfc3389): RFC3389 support > incomplete. Turn off on client if possible > > -- Endpoint 'aaln/1@VG101-1-1' observed '9' > NOTICE[20501]: File rtp.c,

Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,

Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4

Hello List, I'm trying to setup MGCP channel with a Centile Media Hub box. My Centile box has 4 ports and I got no dial tone. Can somebody help with this isuue? This is my mgcp.conf and extensions.conf Thanks Daniel. ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 192.168.11.20 disallow=all allow=g729 allow=alaw allow=ulaw [192.168.11.200] context=MGCP

ONLY ON MONDAY! Well it used to work - calls between my aaln's that is. I moved from debain to redhat (same conf. files for asterisk) and this is what I get.. looks like several errors. errors I never got before. Also asterisk isn't observing the digits as I dial them like it used to however it still trys to route the call when I'm finished dialing. Anyone with a though on this?

I had MCGP working to a ADIT 600 fine with debain sarge stable / asterisk stable - wanted to try red hat and got the below message - then I re-installed debian and am still getting the same message below - any comments are greatly appreciated - I did play with the config files with no prevail - the Adit seems to be doing its job per tech support at CAC. I listed my conigs below I go off hook

I'm trying to use a 4 port ATA that was designed for use with MGCP 1.0 / NCS 1.0 -- is the channel_mgcp compat with NCS -- anything I can do to make it compat?? This is what happens - below *CLI> mgcp reload Reloading MGCP == Parsing '/etc/asterisk/mgcp.conf': Found Use EXIT or QUIT to exit the asterisk console == MGCP Listening on 10.1.22.39:2427 == Using TOS bits 0 mgcp

Hi, in following of a recent discussion I got to work on MGCP with the Cisco ATA186 again, and got it to work very nicely. However, there is a little thing with transfers I would like to get comments on: Call comes in from PSTN and goes to an ATA186 (MGCP) Call is answered and then, using flash, transferred to another extension If the extension is available, there can be an announcement and