similar to: Ring requested on channel 1 already in use...

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

Hi, I am getting this message on the * console on my first pri span. Pri show span show it is down, and I can't make any calls from the span. Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27

Hi all, I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns QuadBRI running in NT-mode. Connected to the BRI-Ports are 12 Fax-Modems (Elsa MicroLink ISDN/TL V.34) which are only operating in dial out analog mode to deliver fax messages. After a while of running fine (50-200 dial out connections) on some S0 spans the following message occurs

hello all, i'm using TE110P and all configuration prosess is done. but after i do the 'modprobe' for zaptel and wcte11xp, follow by ztcfg -vv and asterisk -vvvgc i have this error. *CLI> May 27 14:44:33 WARNING[3059]: chan_zap.c:8534 pri_dchannel: PRI Error: We think we're the network, but they think they're the network, too. May 27 14:44:34 WARNING[3059]: chan_zap.c:8534

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi. I'm getting the following error at random intervals on my TE410P with Asterisk CVS-03/30/04-11:49:01-CEST. I have two spans active, one connected to my Telco, the other to a Siemens PABX. Both spans display this behavior at random intervals. All calls are dropped when this happens. Spans are not necessarily in use when this happens.

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

I am trying to test out my PRI configuration on a server by conection another asterisk server to it. I have the T-1 cards up and both set to bchan=1-23 and dchan=24 in zaptel.conf I am getting lost on the signalling in zapata.conf. using pri_cpe makes sense for my target box, but I am getting the following errors on my source box if I use pri_net or pri_cpe signalling. May 31 17:15:06

I've read as much as I can on this error and still can't seem to figure out what's causing this error: Jun 23 20:54:58 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]:

Hi all, I need the zap channels going, but got the following error. What do I need to change in my configuration? Thnx. chan_zap.c: In function `zap_send_keypad_facility_exec': chan_zap.c:2309: warning: implicit declaration of function `pri_keypad_facility' chan_zap.c: In function `pri_dchannel': chan_zap.c:9292: structure has no member named `call' make[1]: *** [chan_zap.o]

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

We've had a recurring issue on one of our servers where one or more zap channels from a PRI will get "stuck" causing incoming calls to fail. I happened to have a CLI session when it happened this morning. The start of the problem looked like: -- Channel 0/3, span 1 got hangup -- Channel 0/3, span 1 got hangup Jul 18 08:34:54 WARNING[20343]: chan_zap.c:7585 pri_dchannel: Ring

Hi all, I have 1 Card Digium TE412P and 2PRI E1. I have more problems with drops lines. The asterisk log is this: May 16 10:52:26 NOTICE[4465]: chan_zap.c:8194 pri_dchannel: PRI got event: Alarm (4) on Primary D-channel of span 1 May 16 10:52:26 WARNING[4465]: chan_zap.c:2287 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! May 16 10:52:26 NOTICE[4465]:

Hi guys, I've been trying to get my ISDN-10 line up for the past few days, but its been going up and down. I am using OpenVox D110P card on asterisk version 1.4.21. It seems to me like a cable problem. I tried using Ethernet straight cable (12, 45, 36, 78) and also a "straight" cable where the twisted pairs are on 12, 34, 56 and 78. The problem remains the same.

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

Greetings to all, I am getting the following error on my PRI-connected Asterisk box, and am just wondering if anyone else has seen this, and if so how they solved it. Jan 18 10:10:23 NOTICE[6070]: chan_zap.c:7428 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Jan 18 10:10:24 NOTICE[6070]: chan_zap.c:7428 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

Hi, I still cant dial out on Zap and I really have no clue why. I'm using Asterisk Asterisk 1.2.6 and Zaptel 1.2.5 with Digium card 4 ports, 31 channels each and able to receive incoming calls and fax perfectly. I've done this in my dial plan. exten => 111,1,Answer() exten => 111,n,Ringing() exten => 111,n,Wait(2) exten => 111,n,AbsoluteTimeout(30) exten =>