similar to: mgcp audiocodes mp200

Greetings; We are trying to get Asterisk up and happy at our site-we tried VOIP using Sphere about a year ago, spent a *boodle* on expensive hardware and services from a local "expert", but it never was happy. I'm brand-spanking new at VOIP, and I've learned a *ton* getting Asterisk breathing in the last couple of days. I have three Polycom Soundpoint IP 500 SIP phones, which

guys, what firmware version of audiocodes mp104 fxs are you using with asterisk? i'm having sip stack problems. ~kelvin -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030916/50d5f5de/attachment.htm

> > I am looking for "how to" information / references on use of either Audiocodes MP104 or 108, or Vega 50 Gateways for interconecting Asterisk to the PSTN via FX0 interfaces. > > Any info of references / personnal experiences would be appreciated > > Stratus? THE WORLD'S MOST RELIABLE SERVERS * > Richard C. Sparacino > Telecom Technology Manager

We're trying to use some AudioCodes MP104 FXO units as gateways to Asterisk but cannot get them to reliably detect DTMF. Some landline calls get most digits but some are duplicated. Some cell phone calls get 0% DTMF recognition. Anyone with experience with these units have any suggestions? ABP Technical Support has been unable to diagnose the problem and is now sending random guesses and

Sir, Here is the working Audiocodes MP-11X FXO configurations to work with Asterisk. ;************** ;** Ini File ** ;************** ;Board: MP-118 FXO ;Serial Number: 905371 ;Slot Number: 1 ;Software Version: 5.00A.024 ;DSP Software Version: 204IM => 209.13 ;Board IP Address: 192.168.0.195 ;Board Subnet Mask: 255.255.255.0 ;Board Default Gateway: 192.168.0.1 ;Ram size: 32M Flash size:

I'm trying to connect this FXO GW without any success 1) I had to configure the " " to "allow any SIP to connect , so there will be a connection. afte that when I'm dialing I get a noise. I read on the internet that I have to change the impedance (?) 2) I could not find any HOWTO configure this combination - I read that it is a lot of pain to configure the Mp10x but than

I have the following upcoming install and I'm trying to do it without having to resort to Digium t1 cards. I have a Cisco IAD2431 being installed by our Carrier. That Carrier will be providing 2 IP Trunks via ethernet handoff into the Cisco IAD2431. The CIsco IAD2431 has Two T1 ports installed and we would have to install a digium card to support those two t1's. What I'd like to do

Hello all, I'm working on a little project right now and have ran into a snag. Was hoping someone would be kind enough to give me a few pointers to help me get past the current issue... I have an AudioCodes MediaPack MP-114 (2FXS and 2FXO... SIP firmware...) that I'm trying to get to play nice with Asterisk 1.4. I've got it to the point where the AudioCodes box picks up

I have some Audiocodes units which appear to be running Linux, according to the unit's own "System Log" kern.warn Linux version 2.4.21openrg-rmk1 #2 Wed Aug 30 17:05:29 IDT 2006 However my contact at Audiocodes claims otherwise On 12/4/06, Yaniv Nizan <Yaniv.Nizan@audiocodes.com> wrote: > > > > I doubt that we are running Linux on the MP-202. Perhaps there is a

I have an Audiocodes MP-118FXO in production. When an outbound call is made and the remote party hangs up, the Audiocodes hangs up the call immediately. But if an incoming call is received and the remote party hangs up, the Audiocodes does not hang up immediately. I have tinkered with Current Disconnect and Polarity Reversal settings, to no avail. Anyone experienced this issue with Audiocodes or

Is anyone on the list using an Audiocodes gateway with asterisk and SIP? I'm looking at that platform, but I have a couple of issues: 1) Echo cancellation. The echo that I'm hearing with an X100P is unacceptable. Does the Audiocodes do better? 2) Line signalling. I'm using Kewlstart with the X100P, but it looks like the audiocodes uses loopstart only. How does this work with

Is anyone on this list using and audiocodes FXO gateway? I have Asterisk(1.07 on OS X) setup and working fine, including SIP phones and IAX2 phones - I can make outbound calls just fine and receive inbound calls just fine. However, I can't seem to find the right series of DTMF settings on the AudioCodes to allow DTMF tones to be sent after an outbound call is connected(phone banking,

Hello, I'm helping a colleague (*) which has the following setup: ITSP --- <T.38 capable PJSIP trunk> --- Asterisk 13 --- <PJSIP>-- Audiocodes MP-112 --- <FXO/FXS> --- Fax machine My issue is the following : Audiocodes gateway reject INVITEs with 488 Not Acceptable Here It seems this gateway requires t38 settings to be present in SDP body in the very first INVITE. My

Jerry and Michael, many many thanks for your posts. Erick. On 5/24/06, The VoIP Connection <asterisk-biz@thevoipconnection.com> wrote: > Here are the step by step instructions for setting up a brand new Audiocodes > FXS gateway for use with an Asterisk server: > > Connect the gateway to a network switch and connect a computer to the same > switch. Then configure the IP

Hi I have asterisk 1.4 I want to make a MGCP trunk as a client to connect to a provider who is using MGCP protocol, he provided me with user & password, I tried a custom trunk: MGCP/$OUTNUM$@user:password at 66.152.163.106:4000 Not seems to help, Any suggestions plz?

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

Hi list, I'm trying to get ready the MP-104 FXO to use qith my box, but when I send calls I hear only dial tone and after a few seconds I get busy signal. I very appreciate your advices. Command line results and SIPconfigurations follows: *CLI>* -- Executing [7991696900 at total:1] Playback("SIP/101-09dd8918", "beep") in new stack -- <SIP/101-09dd8918>

Has anyone used the AudioCodes MP-20x? http://audiocodes.com/Objects/Analog_Telephone_Adapter_Series_MP_20X.pdf Seems like a good device, but I can't seem to find anyone actually using them... -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061022/6ca85b8c/attachment.htm

Hey guys, can you shead some light on this? I will copy my mgcp.conf and post below, but here is the problem. I can't get call waiting to work with my MGCP device. I already have one call going, and I can hear the second call come in, I flash over to it, but all I get is a dial tone, * puts the 1st call on mute/hold, but I never get the second, and it terminates. I flash back over and pick

I'm having problem passing Caller ID to asterisk from AudioCodes MP-114 (FXO) AudioCodes is passing the caller ID to Asterisk but Asterisk is trying to interpret it as authentication: [Dec 31 11:41:07] WARNING[9752]: chan_sip.c:8553 check_auth: username mismatch, have <pstn-5665>, digest has <pstn-1270> [Dec 31 11:41:07] NOTICE[9752]: chan_sip.c:14316 handle_request_invite: