Erick Perez
2006-May-25 06:49 UTC
[asterisk-biz] RE: [Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP
Jerry and Michael, many many thanks for your posts. Erick. On 5/24/06, The VoIP Connection <asterisk-biz@thevoipconnection.com> wrote:> Here are the step by step instructions for setting up a brand new Audiocodes > FXS gateway for use with an Asterisk server: > > Connect the gateway to a network switch and connect a computer to the same > switch. Then configure the IP address of the computer to 10.1.10.2. Then run > your web browser and point it to http://10.1.10.10 and login using the > information below. > > Default IP address: 10.1.10.10 > Default user name: Admin > Default password: Admin > > Goto "Quick Setup" and change the following: > IP Address => Set to the new IP address of the AudioCodes gateway > Subnet Mask => Set to the correct netmask for your local network > Default Gateway Address => Set to the correct gateway IP address for your > local network > Working With Proxy => Set to "Yes" > Proxy IP Address => Set to the IP address of the Asterisk server > Enable Registration => Set to "Enable" > > Restart the gateway then log back in using the new IP address. > > Goto Protocol Management -> Protocol Definition -> Proxy & Registration > Registrar IP Address => Set to the IP address of the Asterisk server > Registration Time => Set to "60" > Subscription Mode => Set to "Per Endpoint" > Authentication Mode => Set to "Per Endpoint" > > Goto Protocol Management -> Protocol Definition -> DTMF & Dialing > Max Digits In Phone Num => Set to a large enough number such as "32" > > Goto Protocol Management -> Protocol Definition -> Coders > Add coders as needed You need to set at least G.711U-law > > Goto Protocol Management -> Endpoint Settings -> Authentication > Set SIP username and password for each port > > Goto Protocol Management -> Endpoint Phone Numbers > Enter an extension (phone) number for every used channel > > Your AudioCodes gateway is now ready. > > Michael Crown > Managing Partner > www.thevoipconnection.com > 321.989.6728 ext. 611 > sip:611@voiceserver.thevoipconnection.com > > > -----Original Message----- > > From: billy@kersting.com [mailto:billy@kersting.com] > > Sent: Wednesday, May 24, 2006 10:23 PM > > To: asterisk-biz@thevoipconnection.com > > Subject: RE: [Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP > > > > FXS > > > > -----Original Message----- > > From: asterisk-users-bounces@lists.digium.com > > [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of > > The VoIP Connection > > Sent: Wednesday, May 24, 2006 9:25 PM > > To: 'Asterisk Users Mailing List - Non-Commercial Discussion' > > Subject: RE: [Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP > > > > FXS or FXO? > > > > Michael Crown > > Managing Partner > > www.thevoipconnection.com > > 321.989.6728 ext. 611 > > sip:611@voiceserver.thevoipconnection.com > > > > > > > -----Original Message----- > > > From: William Piper [mailto:billy@kersting.com] > > > Sent: Wednesday, May 24, 2006 6:27 PM > > > To: 'Asterisk Users Mailing List - Non-Commercial Discussion' > > > Subject: RE: [Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP > > > > > > Sorry to hijack your thread. > > > > > > Reading these posts made me grab my old MP-104 & try again > > to get it > > > working with asterisk. I bought it a while ago off eBay & > > never could > > > get it to register. > > > > > > Does anyone have an example ini file for the MP-1XX that I > > could look > > > at & figure out what I am configuring wrong on this box? > > > > > > Thanks, > > > > > > bp > > > > > > -----Original Message----- > > > From: asterisk-users-bounces@lists.digium.com > > > [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Jerry > > > Jones > > > Sent: Wednesday, May 24, 2006 6:04 PM > > > To: Asterisk Users Mailing List - Non-Commercial Discussion > > > Subject: Re: [Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP > > > > > > From my copy of the manual > > > > > > > > > MP-1xx SIP User's Manual 36 Document #: LTRT-65404 You can use the > > > 'Reset' button to restore the MP-1xx networking parameters to their > > > factory default values (described in Table 4-1) and to reset the > > > username and password. > > > Note that the MP-1xx returns to the software version burned > > in flash. > > > This process also restores > > > the MP-1xx parameters to their factory settings, therefore you must > > > load your previously backed- up ini file, or the default ini file > > > (received with the software kit) to set them to their > > correct values. > > > To restore networking parameters to their initial state, > > take these 6 > > > steps: > > > 1. Disconnect the MP-1xx from the power and network cables. > > > MP-1xx SIP User's Manual 4. Getting Started 2. Reconnect the power > > > cable; the gateway is powered up. After approximately > > > 45 seconds the Ready LED turns to green and the Control LED > > blinks for > > > about 3 seconds. > > > 3. While the Control LED is blinking, press shortly on the reset > > > button (located on the left side of the front panel); the gateway > > > resets a second time and is restored with factory default > > parameters > > > (username: "Admin", password: "Admin"). > > > 4. Reconnect the network cable. > > > 5. Assigning the MP-1xx IP address (refer to Section 4.1 > > on page 35). > > > 6. Load your previously backed-up ini file, or the default ini file > > > (received with the software kit). > > > To load the ini file via the Embedded Web Server, refer to > > Section > > > 5.9.2.1 on page 120. > > > > > > > > > > > > > > > On May 24, 2006, at 3:00 PM, Erick Perez wrote: > > > > > > > Just a question, has anyone knows how to blank or factory > > reset an > > > > AudioCodes MP124-C/FSX/AC/SIP unit (it's a 24 FSX to SIP unit). > > > > I purchased them second-handed with no manuals (thank god for the > > > > internet!!) but i guess the pdf manual I have does not have the > > > > section of factory-reset. > > > > > > > > Also, any sucess stories with: > > > > AudioCodes MP124-C/FSX/AC/SIP > > > <--->Asterisk<---internet<--->Vonage > > > > setups? > > > > > > > > Thanks, > > > > > > > > > > > > -- > > > > > > > > ------------------------------------------- > > > > Erick Perez > > > > Linux User 376588 > > > > http://counter.li.org/ (Get counted!!!) Panama, Republic > > of Panama > > > > _______________________________________________ > > > > > > > > > > > > > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com -- > > > > Asterisk-Users mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > __________ NOD32 1.1556 (20060525) Information __________ > > > > This message was checked by NOD32 antivirus system. > > http://www.eset.com > > > > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-biz mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-biz >-- ------------------------------------------- Erick Perez Linux User 376588 http://counter.li.org/ (Get counted!!!) Panama, Republic of Panama
Thank you for your help, however I still cannot get this thing to connect to asterisk. I followed your instructions to the letter & couldn't get it to connect. I'd be happy to throw it up on a public IP if anyone would like to take a crack at getting it to work. Thanks, bp On 5/24/06, The VoIP Connection <asterisk-biz@thevoipconnection.com> wrote:> Here are the step by step instructions for setting up a brand newAudiocodes> FXS gateway for use with an Asterisk server: > > Connect the gateway to a network switch and connect a computer to the same > switch. Then configure the IP address of the computer to 10.1.10.2. Thenrun> your web browser and point it to http://10.1.10.10 and login using the > information below. > > Default IP address: 10.1.10.10 > Default user name: Admin > Default password: Admin > > Goto "Quick Setup" and change the following: > IP Address => Set to the new IP address of the AudioCodes gateway > Subnet Mask => Set to the correct netmask for your local network > Default Gateway Address => Set to the correct gateway IP address for your > local network > Working With Proxy => Set to "Yes" > Proxy IP Address => Set to the IP address of the Asterisk server > Enable Registration => Set to "Enable" > > Restart the gateway then log back in using the new IP address. > > Goto Protocol Management -> Protocol Definition -> Proxy & Registration > Registrar IP Address => Set to the IP address of the Asterisk server > Registration Time => Set to "60" > Subscription Mode => Set to "Per Endpoint" > Authentication Mode => Set to "Per Endpoint" > > Goto Protocol Management -> Protocol Definition -> DTMF & Dialing > Max Digits In Phone Num => Set to a large enough number such as "32" > > Goto Protocol Management -> Protocol Definition -> Coders > Add coders as needed You need to set at least G.711U-law > > Goto Protocol Management -> Endpoint Settings -> Authentication > Set SIP username and password for each port > > Goto Protocol Management -> Endpoint Phone Numbers > Enter an extension (phone) number for every used channel > > Your AudioCodes gateway is now ready. > > Michael Crown > Managing Partner > www.thevoipconnection.com > 321.989.6728 ext. 611 > sip:611@voiceserver.thevoipconnection.com