similar to: MGCP - Repost

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4

I'm confused a bit about the following and was hoping to get some answers on this group - What is exactly implied when we say asterisk can connect to a PSTN. Does it mean connecting to the PSTN via PRI/T1/E1? If yes, then I assume asterisk does not need to do any SS7 signaling and all it does (playing the role of a PBX) is to connect to a Class 5 Switch at the CO. Is this a correct statement?

hi all I'm being spammed by these messages in the console (see below) and sound doesn't work with today's cvs. I rolled back a week, and it works fine. In addition to the sound problems, I had to enable inband dtmf squelch on the dilnk mgcp phones. if not, each pressed key was counted twice NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process

I have the following setup: AnalogPhone1--TDM400P-ASTERISK---via SIP---Softswitch--------POTS Phone2 When I call from AnalogPhone1 to Phone2 I hear a ringing tone and all is well. When making a call from Phone2, I get a dial tone but after dialing the number I hear nothing (no ringing tone). On Asterisk console it says that a call is coming in and that it is ringing Zap/2. I can also hear the

Hello Everyone, What kind of hardware setup would I need to do if I want a T1 connection to PSTN and have 48 users in office with analog phones. Will something work if I have a T410P card in asterisk and have one T1 going to PSTN and other two to a channel bank. I would then connect the 48 phones (FXS) to the channel bank! Thanks. Deepak

hi all I'm trying to use the manager interface to do some nagios (http://nagios.org/) integration, and I find some parts of it not really optimal. What I'd like to change, is to make \r\n\r\n an actual terminator, something it isn't today, AFACS. Below is the Status output - it shows Response, Message, \r\n, Status post, \r\n, Status post etc etc. Without a parsable terminator, I

hi all when I (using my D-Link DPH-100M MGCP phone) press #, I get told 'transfer'. I dial the new number and after that, * just tells me 'meep meep meep' [hangup] any ideas why? -- Roy Sigurd Karlsbakk, Datavaktmester ProntoTV AS - http://www.pronto.tv/ Tel: +47 9801 3356 Computers are like air conditioners. They stop working when you open Windows.

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

I have following setup: AnalogPhone_1--TDM400P--Asterisk---SIP---[Softswitch]----POTS-AnalogPhone_2 I can call from AnalogPhone_1 to AnalogPhone_2 and all is fine. When I call to AnalogPhone_1 from AnalogPhone_2, AnalogPhone_1 rings BUT I hear no ringing tone AND when someone picks up AnalogPhone_1, there is no "sound" and parties on both end cannot hear each other. Seems that no

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,

Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one

Hello List, I'm trying to setup MGCP channel with a Centile Media Hub box. My Centile box has 4 ports and I got no dial tone. Can somebody help with this isuue? This is my mgcp.conf and extensions.conf Thanks Daniel. ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 192.168.11.20 disallow=all allow=g729 allow=alaw allow=ulaw [192.168.11.200] context=MGCP

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb:

Hello everybody! I have an Asterisk 1.2.12.1 server with SIP as the VoIP protocol. What I want to do: I want to talk to the "outside world" via MGCP. I suppose I must set an MGCP peer to route outgoing calls. So, I must set the endpoint syntax of the Asterisk server (Asterisk will act as an MGCP gateway and will talk with an MGCP Gatekeeper) and with other MGCP gateways via

Hello, I have just received an MGCP Phone for test purpose and I can't place a call from my MGCP Phone. I can call my MGCP phone from a SIP Phone. Here is my mgcp.conf: ; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr = 0.0.0.0 ;[dlinkgw] ;host = 192.168.0.64 ;context = default ;line => aaln/2 ;line => aaln/1 [192.168.10.10] host = 192.168.10.10 context =

Hi everybody, I have a MTA from Terayon that I try to make run with Asterisk using MGCP channel. The device is running with MGCP 1.0 NCS 1.0 Each time Asterisk try to send a Request (Request Notify, Audit Endpoint....) the device returns error 510 "Protocol Error" Does anybody have already meet this problem and provide me support to make run it ?! (I have already try to change

Hi I have asterisk 1.4 I want to make a MGCP trunk as a client to connect to a provider who is using MGCP protocol, he provided me with user & password, I tried a custom trunk: MGCP/$OUTNUM$@user:password at 66.152.163.106:4000 Not seems to help, Any suggestions plz?

Good Morning, I'm having an issue with callerid display when calles are placed _from_ an mgcp device (8x8 ata w/mgcp firmware). Internally, there are several different sip devices and one mgcp device. Calls from any of the sip devices to any other device (sip or mgcp) have name/number displayed properly by the called party's phone. Calls from the mgcp device to any other device display