similar to: ISDN PBX + IVR + Voicemail Configuration - Sanity Check ...

Klaus-Peter (while hardly able to see through my watery eyes), You've earned yourself a (potentially rackmountable) 19" Dutch cheese as soon as the zaptel driver is finished and tested. In fact, I don't even have to mail it, I can pratically bring it over ! Although I'll be monitoring your site on a 24hrs/day basis from now on, please keep me posted on both the driver and the 4

Guys, I am planning on building a small SIP PBX with a single ISDN line. Currently I am looking into the specs of a very tiny barebone system that has an option Colognechip base ISDN controller. The only thing is that the ISDN module that comes with this barebone hooks up to the motherboard using USB. My intention is to allow incoming and outgoing calls from SIP to ISDN. Is this setup in any way

These allow and disallow work with NuFone for me disallow=all allow=ulaw allow=alaw allow=gsm Jeff Message: 11 Date: Fri, 11 Mar 2005 11:15:51 +0100 From: "Edward Banfa" <edward@radform.com> Subject: [Asterisk-Users] NuFone Configuration [problem] To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" <asterisk-users@lists.digium.com>

hi, i just found a page on the net which might me worth some lines. for the urgent reader: http://isdn.jolly.de there is a guy in germany who has successfully programmed a gpl-patch for isdn4linux to make isdn cards with the hfc chipset from cologne chip (http://www.colognechip.com) run in the NT mode (up to 2.4.20). this mode is needed to connect isdn device to a pc and enables the use of

Hello, Does anyone know what driver to use with an "Eicon Diva Server 4BRI" card? My modem.conf: -------------- [interfaces] context=remote driver=i4l msn=16453 device => /dev/ttyds01 -------------- I get the following error: -------------------------- == Loading modem driver chan_modem_i4l.so => (ISDN4Linux Emulated Modem Driver) WARNING[8192]: File chan_modem.c, Line 383

Could someone please comment on the current state of chan_capi, chan_misdn and chan_modem channel drivers in terms of functionality and stability. Specifically, which channel driver would be best for a passive PCI HFC or W6692 ISDN card. The chan_misdn wiki claims that chan_capi distinguishes between junghanns and non-junghans cards, and that chan_misdn is better suited for general misdn

Hello all - This is my situation! I have a PC with no PCI slot and no modem! But I would like to install asterisk on it. I want to use SIP based software ONLY with the asterisk PBX system. I already have the asterisk running on a regular PC. BUt when I run assterisk it fails at this point when it parse modules.conf file. [Wait] == Registered application 'Wait' Asterisk Dynamic

Hi everybody and sorry for posting this again to the list. I don't want you guys to think that I'm DEMANDING FOR SUPPORT (we all have just had several discusions about that) but my experience tell me that if a posted question is easy enough, it is answered immediatly, or it will never be answerd!!!(people forget it...) Mine are two very simple questions about modules.conf. It's only a

When I attempt to start asterisk with my modem setup listed it will not start attached are the error messages i get and also the modem.conf that i am currently using. Any assistance would be greatly appreciated. running CVS ver 12/7/03, modified only to allow the RxFax and TxFax to compile and run with it (from http://www.opencall.org) just e-mail me privately if you need more info Thanks in

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

Hi, I am currently running several * boxes on 1.0.9 with HFC chipset ISDN modems using i4l's hisax driver and chan_modem. Will I be able to use my existing chan_modem setup with 1.2.4 or 1.2.7 or will I need to change it to use bristuff or chan_capi? I want to do the upgrade with as little changes as possible. Thank you Marnus van Niekerk -- "Opportunity is missed by most people

Hi I tried to install the * in my Radhat 7.3 machine. The "gmake" and "gmake install" went fine, but "gmake sample" gave me errors of "configs/*.adsi", "sounds/demo-*" and "sounds/*.mp3" errors. I created a dummy.adsi in the configs folder and commented out the "sounds/demo-*" and "sounds/*.mp3" in the Makefile to

Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:

Hello list, Why PC modems were not used as FXO devices? Why chan_modem was deprecated? it seemed a nicer option instead of buying expensive gateways. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20090802/abb21767/attachment.htm

Hello List! I finally got asterisk with capi working, and its already answering my call as well! :) Now i would like to call a number from my shoft phone (kphone). This is my extentions.conf: --- [general] static=yes writeprotect=no [globals] CONSOLE=Console/dsp ; Console interface for demo IAXINFO=guest ; IAXtel username/password

I'm new to asterisk and fror a cupple of days I heave been googleing the net for digium "clones", because it's very hard for me to get a digium card (X100P). Does anyone Know another substitute for X100P (I know that intel based modem with chip 537/MD3200 is working but I did not find any of those) ? I made it work with an Intel 536 (with a costumised driver that I found on

This is my second attempt trying to get help and I am hoping someone can. When the musiconhold extension is matched, Asterisk attempts to execute musiconhold and stops right away, this is what I gets: Executing MusicOnHold("OSS/dsp", "") in new stack -- Started music on hold, class 'default', on OSS/dsp -- Stopped music on hold on OSS/dsp Is there a file that

I'm trying to use an hfc based pci card with asterisk but every call fails falling in the congestion extension. exten => _0.,1,Dial(${TRUNK}:${EXTEN:${TRUNKMSD}}||tr) exten => _0.,2,Congestion Looking in the syslog i can see: isdn: HiSax,ch0 cause: E001B it seems that this is a terrible error when arrives... hard to tell what is the cause. Also terrible is finding a lot of material

Hi everybody. I'm trying to setting up a V4 BRI EICON card on ASTERISK 1.0.7 My linux is a debian. It was working during a few days an suddenly (after a lot of reboot) I've got this error message that seems to be very popular but I couldn't find any answer on the net : ==============================================. Asterisk Dynamic Loader Starting: == Parsing

Hi, maybe this has been asked before but I couldnt find a proper answer on the web or list. I want to use a analog V.92 modem to make outgoing (and possibly) incoming phone call through a standard analog phone line. I found on web it's easy been done via chan_modem.so module. But this seems removed from asterisk or buggy. So my questions are can I enable chan_modem.so to be built or