similar to: NetJet Cards

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Hello, I am setting up 2 ISDN 4 linux cards and have had great success now that I have got over the initial problems with : and / characters. The only problem I am experiencing now is the sending of DTMF tones over the line to a remote IVR system. If I dial SIP (Cisco 7905 and 7940) to a number over the line, no DTMF tones are heard. I dialed my own home phone and tried it, no matter which

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

G'day, New to Asterisk alert! I have a Netjet card running on linux 2.4.27 kernel using the HiSax module, and trying to use it for incoming/outgoing calls from *. I've tried playing with modem.conf and extensions.conf every which way I can think of, using samples and whatever I can find off the net, and I get the same message everytime I try to dial in. The complete message is:

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hi, I am using a Netjet-s ISDN Card, and am having some trouble dialling out (Incoming Works Fine). TRUNK=Modem/ttyI0 exten => _90XXXXXXXXX,1,Dial(${TRUNK}/${EXTEN:1}||Ttm) exten => _90XXXXXXXXX,2,Congestion I get the following when diallingout: -- Starting simple switch on 'Zap/2-1' -- Executing Dial("Zap/2-1", "Modem/ttyI0/04XXXXXXXX||Ttm") in new

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

I have installed a Billion ISDN card in my Asterisk. Calls between sip and isdn work. The i4l channel has MSN=26. I also put incomingmsn=26,27 in modem.conf. extensions.con: [incoming-isdn] exten => s,1,Dial(SIP/701,20,Ttr) ;will make my extension 701 ring, while exten => 26,1,Dial(SIP/701,20,Ttr) ;will cause an error message in the Cli interface: WARNING[196621]: pbx.c:1814

Hi, I have a problem that I just can't figure out how to solve. I start *, dial it using a ISDN phone over PSTM, to a Hisax card installed in * I get the demo-greeting, listen for a few seconds and hang up. I dial it again, but this time the first second is sound from where the previous call ended, then the greeting starts as it should. Right now I have removed all codecs but codec_gsm.so

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

Hi all, Here another guy working with ztdummy and having problems with music. MP3Player does not work for me both from a telephone entering through a passive ISDN-adapter as well as a SIP-client in the LAN. Ztdummy works with conferences. Here are my messages. I have seen several discussion threads in the mail-archive regarding this subject, but could not find an answer. Is this something I

Hello all, I was wondering if anybody knows where one might obtain a PCI ISDN card supporting a single BRI for use with Asterisk in Australia (and using something like chan_capi). Because of the Isdn4Linux DTMF issue, I don't want one of those cards. I've already spent too much time messing about with my current card. I'm after something like the AVM Fritz! cards. I found one place

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

Hello All, I was just after a few pointers. I have just setup my Redhat 9 linux box with asterisk. Internal SIP call working fine. My Eicon ISDN card turned up today so - plugged it in and went through the modem.conf. It reports unable to open /dev/ttyI0 The problem is I have never used ISDN with Linux - let alone a telephony app - and I have no idea even where to start. Some pointers

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello! After LOTS of research on this list and internet in general I managed to get an old Teles PCI card working with Asterisk throught ISDN4Linux. No echos, no delays, simply perfect -- electronic poetry ! :) eheheheheh I just didn't get it to work with CAPI and "chan_capi" but, since isdn4linux is doing such a good job, I'll

I'm trying using Asterisk over an isdn line. I configured my Eicon Diva card by the hisax module and it works with the Asterisk's chan_modem (and chan_modem_i4l) driver. The problem is that I can receive calls (on /dev/ttyI0) but when I make a call I always have the line busy (on ttyI0 but even if I use an other device like ttyI1). This is a part of my consol output: --

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/gif Size: 4325 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20030331/0fbcd9a7/attachment.gif

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically