similar to: Adtran TA750 & T100P

Hello. I have been going thru the wiki and asterisk related sites and have not been able to find any documentation about how to configure an Adtran TA750 channel bank. The remote disconnect supervision doesn't seem to be working, when the remote caller hangs up asterisk takes up to 30-45 seconds to hangup the call. Can somebody help? Thank's

Rich, Thanks a bunch, totally understand now and that actually makes total sense. (no need for schematics). This also explains why I used an TA750 to go into a Nortel MICS system, using FXO and no buzz. Totally balanced load from the analog ports on the Nortel across the 5 feet of CAT5 to the FXO on the adtran. Now I need to get rid of some Adtrans --- Anyone lookin to buy? :) Thanks

I believe it is not fiber, but I am not sure. I am going to take one of them home tonight and hook it to my POTS line there, which for sure is not fiber. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Michael Welter Sent:

All, I need help. I have an (actually 2) Adtran TA750's with 8 FXO ports. I get a terrible buzz on every FXO port. If I unplug the Adtran and put an analog phone on each incoming line, I have no buzz. I also have 2 Carrier Access Access Bank I's with 12 FXO ports. When I plug the same analog lines into either one of those, no noise or buzz whatsoever. I went so far as to move the TA750

I recently set up Asterisk with an Adtran TA750. All is well except the phones do not show the MWI. I have configured zapata.conf properly, as all phones will receive a stutter dial tone if there is a message waiting in it's assigned mailbox. Does anybody know how I might fix this problem? Thank you for your time __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free,

Hello, I new to this, but with the help of mailing lists archives and IRC I am able to build my PBX. Thanks to all who had help me to reach till here. I am stuck at a point where I can't find the solution on mailing lists or even on IRC. I have individual 4 DID (Direct Inward Line) coming from Telco and terminating into TA 750 to FXS card. Many of them told that Phone instrument terminates

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

> I read your excellent post on the subject. I too am hearing the 60 Hz > hum on the FXO ports of my TA750. One Interesting thing is that it > goes away if there's an analog phone on the same POTS line, and you go > off-hook on it. I guess the analog phone has the repeat coils built > into it, and they balance the line for the FXO port. That's exactly correct; the

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

I have a channel bank (TA750) and a PRI with 30 channels connected to a TE405P, in the channel bank I have a extension to a fax machine, but it doesn't work to send or receive fax. There are any advice ? Kind regards, Miguel

Hello, and please forgive the OT question. I'm just becoming desperate. I need two ISDN 30 circuits in Amsterdam, and I can't seem to be able to get a provider. I've tried KPN and Versatel. I'm based in California. Does anyone have any recommendations? Thanks in advance, Jose.

Hi my question is: which is the best distribution to work with asterisk? thanks mark

I just got my Access Bank 2 (of course i'm happy now:)). Just need the wiring scheme Thanks

Hey, Here's a new swfdec-gnome release to go with the just released Swfdec 0.6 release. Changes: - Depend on Swfdec 0.6 - Support automatic install of missing audio/video plugins - Really translate all relevant strings (Wouter Bolsterle, Bastien Nocera) - Updated ca: Gil Forcada - Updated ar: Ignacio Casal Quinteiro, Djihed Afifi - Updated cs: Petr Kovar - Updated et: Priit Laes - Updated gl:

Hi List, I have some T1 750s; hookup via a T1 to a TE420P card. We have them all set as E&M wink trunks. We get a dial tone and can call numbers, but when i call another number the ringing I hear on my phone is very weird, its not the standard ring tone. What will cause this? Is this a * setting or something in the Adtran I am fixing, I just want good ole ringing to be heard! Any help would

All: Has anyone else on the list had any experience with the new Adtran IP712 phones? I have taken the stock config file and been able to get simple registrations and basic call processing to work properly, however, I'm finding little to no documentation on how to configure advanced options such as BLF/Parking/Definitions for Files (Phonebook,xml,etc). I guess I may be assuming a lot about

TC: You were right on the money. The new firmware L-34 fixed my problem with the Channel Bank. Now the lines are properly closed and not hanging up the lines. One of these days I should read more about the 750. I saw some parameters for "network on-hook/off-hook + test" that I don't even know what they do. Thank you so much. Regards, Uriel -------------- next part --------------

Can I configure an Adtran channel bank with a mixture of FXS and FXO cards and have them come into a single T100P T1 card? It seems like this would be a cheaper solution than trying to load a bunch of PCI cards into a PC. Also, when shopping for an Adtran (on ebay) - what do I need to watch out for as far as interfaces or capabilities to make sure that it works with a Digium card?