similar to: X100P too quiet

Hello, I'm running Asterisk 1.0.6 with zaptel 1.0.6 on Gentoo Linux with a 2.6.11-gentoo-r2 SMP kernel (but no SMP hardware) and mpg123 0.59s-r9. When I leave a voicemail message via my X100P, the message is way too quiet. I can barely hear it. I googled this a bit, and I saw similar complaints with older versions, but no resolutions. Also, many complained that it was only too quiet via

Hello. I've seen several posts talking about line quality using Digium cards that are sharing IRQs or on machines where X is running but after trying all of those fixes I am still having a problem with line static on outoing calls. BTW, calls that are from one extension to another extension have no static, however, they have occasional clicks and pops. At any rate, I was wondering if

I understand that the X100P card is matched to a 600 ohm impedance but the UK BT phone system is not (I haven't been able to find much information on the impedance of the UK system). Has anyone come up with an easy way to match the impedance between the two so the X100P can work in the UK? Presumably a simple transformer won't do the job since it won't pass the DC components? --

I'm looking to get an x100p off ebay and am not particularly familar with the "life cycle" of the card.. An "Authentic X100P" listing has a buy it now of $29.95 and says There are 3 types of cards Asterisk would recognize: *Screenshots from the official, original driver install Cheap "OEM X100P","Clones", "Compatibles", Knock-Offs

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm experiencing frequent kernel panics when using the X100P card under the 2.6.6 Fedora kernel. I've attached the kernel output to this message - - it looks like the IRQ stack is overflowing and trashing some memory, causing a series of oopses followed by a complete crash. I have just hacked the kernel to reenable 8k stacks and will see

I have a pIII system with a x100p card. I've installed everything, got it working, no problems. I had a few problems with echo in calls through the X100p card so I read about enabling KFLAGS+=-DAGGRESSIVE_SUPPRESSOR in the zaptel makefile. After I did this I ran *. All I got was two flashing leds on the keyboard (scroll lock and caps lock). Everything else was frozen. So I thought,

Hi All... I have installed a single X100P card in my PC and am playing with Asterisk. The wire I plugged into the X100P has two POTS lines on it, wired on the RJ45 in the normal way. I am getting odd behavior. It seems when I dial out that the X100P dials both lines at the same time. I have two questions. First, I see that the X100P is only a single channel. Does this mean that I can

Yo all, I have a problem with a Dutch (KPN) PSTN-line, connected to an X100P. The call wil sound OK at first, but after 10-20 minutes, the audio will start to crackle. Soon after that, this crackle turns into a continuous noise and the parties won't be able to hear eachother anymore. It also sometimes happens that the party on the TDM400P hears a very loud, short-delay echo of themselves,

Hi I thought this might be of general interest. Recently I purchased an X100P from a Digium reseller in the UK. Very pleased with the card; works perfectly. My friend (known for his deep pockets and short arms) purchased an X100P card from Ebay. He's had no end of problems with line noise, dropped called etc so I thought I would compare the two cards. Plus mine was delivered within two

I've come across an odd dialing problem with my * setup. After * has been running for a while, if I try to dial out on any of my zap channels, (both are X100P cards) it picks up the line but never sends the DTMF. Has anyone heard of or seen this problem before? Right now I'm looking at 19 hours of uptime on * itself. If I restart it, everything works fine for a little while, then the

Hello, Can anyone tell me what the "normal" number of interrupts per second is for an X100P card? I've used FreeBSD 5.3 and a linux 2.6.11 kernel on the exact same hardware (only the disk changed) and `systat -vmstat 1` on FreeBSD and `procinfo -dS -n1` under Linux. For both, I'm seeing roughly 1000 interrupts per second on my X100p card. It was a bit worse under FreeBSD, and I

Hi all. I`ve installed a X100P on my box and is working well with incoming and outgoing calls as a trunk with one PTSN line. I want to connect the X100P to my Panasonic 616 EASA-PHONE as an internal extension to permit to users to make calls to SIP devices from analog phones, the problem is when I dial the ext number where the X100P is connected I get busy tone. What config I need to change to

Hello, I have X100P card but exten => _9X.,1,Dial(Zap/1/${EXTEN:1}) does not work. The error is app_dial.c:803 dial_exec: Unable to create channel of type 'Zap' (cause 0) Zap show channel, lspci etc show everything is normal. Because X100P is Intel 537 modem, so can I use it as true modem for test? Did any one use X100P as a modem? Thank you very much. -------------- next part

Hello my brothers and sisters, Is "X100P" card suitable to VoIP? and if "yes", am i need to only "X100P" and "Asterisk" Package? or i need also to other cards or packages? and if "X100P" card not suitable to VoIP, please recommend a another card, (please take in your account that i would like to connect standard analog line to the card

My setup: X100P and Quicknet PhoneJack. I can't seem to properly set up a Zap channel for my X100P. Here are some of my configurations: [zaptel.conf] fxsks=1 #X100P fxoks=2 #Quicknet PhoneJack defaultzone=us loadzone=us [zapata.conf] [channels] context=local signalling=fxs_ks channel->1 ;X100P [extensions.conf] ... [local] exten=>_NXXNXXXXXX,1,Dial,Zap/1 ;I'm pretty sure the

If Asterisk is configured as a simple answering machine replacement with the X100P connected to PSTN line. No FXS ports in the Asterisk machine. Standard phones are connect in parallel with the X100P like you would a regular answering machine. Can Asterisk detect that a phone has been picked up and cancel the outgoing message and/or voice recording? What about if the phones are connected to

G'Day, I need from regarding using the X100P. Some are specific to Australia and I have been told in IRC there are already existing users in oz, so I would appreciate your input. 1) Is the X100P Australia telco approved? 2) I have setup asterisk with X100P and whenever I dial in I cannot get any callerid information. Is this standard behaviour? If not how have other australian users managed

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

Hi all, Really excited to be using Asterisk and learning about VOIP and PBX's. I'm a complete beginner at telephony but have built and installed Asterisk 1.4.5 and read several of the Asterisk books online and have successfully connected to FWD with IAX2 and to GIZMO using SIP. Just purchased a Motorola Wildcard X100P and installed it into a clone PC running Fedora Core 6. Analog

I have an ubuntu 8.10 machine. Linux 2.6.27-14-generic i want to configure a x100p card an use it with asterisk, so i download, compile and install: asterisk-1.4.24 dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.9 i try almost everything i found on the net but without success: if i run lspci: 04:06.0 Communication controller: Motorola Wildcard X100P when i run dahdi_hardware appears this: