similar to: monitoring the asterisk and safe restart

Hello All, I am battling a problem I don't know how to fix... Here is the scenario: Fractionated T1 with 1-6 channels voice, 21-24 channels data. Comes into a box with Digium T100P, splits off data channes with HDLC, to devicec pvc0, This works fine, but I have a routing problem getting to my machines! Here is the current set up... sethdlc hdlc0 fr lmi ansi sethdlc hdlc0 create 44

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

Yesterday I started using CBQ in production on our firewall over an IMQ device, but since then I get a lot of messages in my syslog like below: On Wednesday 13 November 2002 09:07, root@ism.nl wrote: > Nov 13 08:01:36 firewall kernel: NET: 1 messages suppressed. > Nov 13 08:12:36 firewall kernel: NET: 1 messages suppressed. > Nov 13 08:18:36 firewall kernel: NET: 1 messages

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the

Hi, I believe the issues raised by this message are the same as mine, more on a commercial sense than for self use, but mostly the same. I've seen posts where real-life installations are mentioned, but not a reference to how Asterisk is working on production (and productive) environments. Any experiences would be very welcome I believe, not only on pure technical, but wider, sense. Thanks

Hello all, My set up is a fractionated t1, with 1-6 voice channels, 21-24 data channels. I have a t100P installed in a amd 1500 with 512meg. Question: In order to set up the data channels, is the following correct? 1) compile new kernel with generic hdlc support 2) compile hdlc from hq.pm.waw.pl/hdlc 3) uncomment KFLAGS+=DConfig_ZAPATA_NET in zaptel makefile 4) compile zaptel, 5 compile rest

All, I'm having a heck of a time getting hdlc to work on kernel 2.6.11.9 .. I compiled hdlc, hdlc_gen, hdlc_cisco, hdlc_raw, into the kernel (note into, and not 'modules'). System comes up, I configured zaptel.conf span=1,0,0,esf,b8zs nethdlc=1-24 modprobe wct4xxp ztcfg sethdlc hdlc0 cisco ifconfig hdlc0 up All of this works fine, believe it or not. I have a T1 cross plugged

Hello all, We have a TE405P set up with span 1 running to a channel bank, a PRI running into span 2, and a PPP internet T1 running into span 3. We have the first 2 spans up and running without a problem. We have hdlc compiled into the kernel and after making the appropriate changes to zaptel.conf and loading the zaptel, wct4xxp, and hldc modules we can bring up the third span with the internet

Hi all, I'm setting up my first * install and have it peering with another * machine using IAX across the internet which provides our pstn gateway. So far I have the IAX "friend" set up correctly but when I make a test call from an external phone, I get: WARNING[5126]: File chan_iax.c, Line 648 (get_timelen): Don't know how to calculate timelen on 8 packets I have set up a

Hi List I have one question about MGCP in asterisk. I have a media gateway, and I want to have asterisk to work with the media gateway. As I was told that the media gateway can communicate with the switch via standard interface MGCP/ICGP. Question is if the asterisk MGCP supports such MGCP message ??? Thanks. George Lin

I got it figured out now. In case anyone else comes across it - this is what I had to do: Sethdlc hdlc0 mode ansi Ifconfig hdlc0 up ***NO IP INFO SET*** Sethdlc hdlc0 create <dlci number> Ifconfig pvc0 <local ip> pointopoint <remote ip> up Then set your default gateway to the <remote ip> listed in pvc0. That's about it!! Hope it helps! -----Original

> From: George Lin [mailto:glin@cosini.com] > > I want to deploy multiple SIPs phone in our office. And we have shutdown > the > firewall at our office router(with ip 211.x.x.x). we have deployed the > asterisk with IP 218.x.x.x. > > All SIP phones have 192.x.x.x. We have something similar George, * sits outside the firewall with a registered IP address, the SIP phones

Hi guys,

Greetings- I'm wondering if the Digium PRI cards can be used for data (Cisco HDLC, PPP, etc) or if they're for voice circuits only. I haven't been able to find any information on this. All documentation direct from Digium seems to indicate their hardware is for voice applications only. Sangoma's cards work in either voice or data mode but of course this is configured in their

hi below is sysvinit script for handling tcng-script .... please excuse my bad bash skils, correct me where i''m doing stupid things :") what is left... many things, if i have time i will implement them too : - start [devices] - and then correct handling of service lock files i.e. per device lock file - stats blah ... - all ideas are welcome !! - test or some such, i mean the

Hi, I am facing problem in configuring D-channel. I did the following configuration for TE-120P card /etc/zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 /etc/asterisk/zaptel.conf group=1 signalling=pri_cpe switchtype=euroisdn context=incoming channel=1-15,17-31 DIGIUM card is connected through cable to another end.On placing call from other end to

Hello lartc! I have strange problem setting load balancing over 4 interfaces. Something won''t accept more than 3 interfaces, While setting: ip route add default scope global \ nexthop via 0.0.0.0 dev pvc0 weight 1 \ nexthop via 0.0.0.0 dev pvc1 weight 1 \ nexthop via 0.0.0.0 dev pvc2 weight 1 It''s ok: ip r l default nexthop dev pvc0

List members; I have been reading the digest for some time now and I would like to ask some conceptual questions. I am a telecommunications systems designer and not a software guy, but I have tried and used a number of the tools availabel in the LARTC and Iptables, and many of the other great things included in Linux. We are designing commercial products and I don''t want to ask my

Hi All, I''ve been playing with QOS for a short while now and have worked out how to do what I want using HTB. Great queuing discipline btw. My problem is the tc filters I want to setup aren''t working because iptables is getting to the packets first and mangling the src address. The iptables script I am using is MonMotha''s Firewall 2.3.8 and it includes lots of nice

Hello, I''m trying to boot kernels from the 2.6.23.x line as paravirt domUs, 64-bit xen-3.1.0 and xen-3.1.2 are used on the test boxes. xm create starts up the domU without any problems according to the logs, however, the started domU does not output anything apart from a single tab (if I start it with -c option ), and eats up 100% CPU. Config file of the domU is as follows: ----