similar to: Has anyone got * working with Xten soft phones

I have seen a couple of messages on the Xten and the work done by William Walsh (Kudos). It is not clear in my mind the advantages of SIP phones versus using GnoPhones (once we complete the work for the Windows version). Since I lack the experience with IP SIP phones, can someone, high level, tell me when it makes sense to use them. Is it complicated to set up on the Asterisk side? Thank you.

I've got the XTEN Lite soft phone mostly working with * but it's dropping out like a very bad cell phone call. The GSM codec is worst (unusable), G711u and G711a are best but not good enough to use. I don't think it's a lack of bandwidth. What tuning options or approaches should I be investigating to make this work. Also, what's the best soft phone(s) for Windows XP?

hi there! I have a couple phones connected to a sipura ata and if I go into *- IVR, I press options on the regular phones and it all works fine and dandy. then I connect an xten softphone, a new extension in my dialplan, I dial the ivr, * asks me to dial something to go through it, I press keys on xten, but nothing happens, * just times out through as if I did not press anything! is there some

Which rpm has libstdc++.so.5? xten-xlite for linux says it needs this. Of course, there will be something else it will need after I get this....

hi xten.de produced an activex for web phone. but I can not find any link for download. can u help me ? best Mani ____________________________________________________________________________________ Now that's room service! Choose from over 150,000 hotels in 45,000 destinations on Yahoo! Travel to find your fit. http://farechase.yahoo.com/promo-generic-14795097

Hi, I'm experimenting with the dev kit lite and now past the USB unpleasantness it's working great with standard phones and lines. The priority right now is getting soft phones (under Windows XP) working well. So far, I've only been able to get the XTEN Lite phone working and I really don't understand how I set it up. I used "xten" for every option everywhere (display

Hello Everyone I just bough my Xten Eyebeam but i don figure out how to make the video works i only see a black screen where de remote video suposse to appear, Any help regarding this matter will be very preciated Thank You

All, I have my * box NAT'd with all ports forwarded that are SIP related (based on Wiki). I also have nat=yes, externalip=WAN address of firewall, internalip=LAN network of *. I have my Xten soft phone on a PC which is NAT'd behind firewall with ports forwarded. I have also followed instructions on Wiki for Xten. I can authenticate fine, and sip show peers shows my extension is OK,

Sorry, I don't remember who was asking about this, but it seems that if you record a video message that contains the send video start, it will actually fire up the remote receive window. I.E. Previously I was using the recording section of voicemail to create my video IVR's. This meant that when I arrived at the section to record the message, I had already clicked send video in Xten.

Dear Guys, I?ve test Xten Lite softphone to connect to my Asterisk Box but it registers all the three lines at the same time and if I try to dial an extension it tries to reach 3 Ext. at the same time, can somebody haved this trouble? and how can I fix it. Also, I ?ll like to have the Xten LITE or PRO Softphone (Lite is free and PRO about $50.00 USD) it can hanle 3 lines (lite) and 6 lines

Guys. Im writing this because Ive checked the wiki, Xten website and read a lot of docs and still cant figure out a way around the NAT issues. Maybe somebody else can give me some ideas from a fresh perpective. My test setup is this: Asterisk -> 2wire homeportal Firewall -> internet Computer with Xten eyebeam The asterisk box and the computer with xten beam are behind the same

Hi folks, well the easiest soft phone I have found (from this list) is the x-ten. great little piece of software. BUT, on a windows machine I need to plug in a USB device and find the software to drive it which can actually use a normal handset (similar to the s100p) but can be used to actually generate/answer the calls and actually rings when a call is received. Any ideas ?? Gary .

I have d/l the iso (*@home 0.9) , built the * box and followed the directions in the * handbook and http://www.geekgazette.com/index.php?option=com_content&task=view&id=2&Itemi d=26. I created extension 200 and verified that * was running fine. Loaded Xten lite, setup the proxy for local ip (10.0.0.201) per the handbook. After turning off the Norton Firewall protection, I am able to

Hi Folks, I am wanting advise on a good soft-phone on Linux. I have looked at Gnophone but cannot seem to get it to compile under debian sarge. I am now looing at sipXphone seem to be picking up that it is not that stable, but perhaps someone here can advise on what softphone I can use on Linux. Thanks in advance, Hamish ------------------------------------------------------------------- |

I have read loads of the emails on the subject but have not read a setup I could use. I have a windows box using Winproxy to dial up the internet through a DSL modem. My internal network I am using while developing. My internet network has been renumbered so that I could test using Nikotel4Mac. It will only accept certain numbering schemes so I have changed my ip's on the internal network

Does anyone have any experience with an Asterisk compatible softphone application which meets the following criteria: 1) Is able to use touch screen rather than mouse for on-screen functions. 2) Has an API which can be used to export Caller ID info to another App on the same compuer. Thanks Bill

Ok I have a question. I have Xten-lite working with our Asterisk system and I am able to make and get calls. But the main problem is the sound is very choppy and sometimes it cuts off words. I have tested it with ulaw and alaw as well as GSM. They all do the same. ulaw seems to work better. I also have an ATA-186 which works great without this problem. Here is my Sip.conf settings.

from: http://www.xten.com/index.php?menu=download Seems to be working fine. just untar and run. But now I have to do some real voice testing. Not to my desk phone 2 feet away and get blasted with feedback!

I've just down loaded Xten Lite and it is now build 1079. It now finds the NAT firewall type and has loads more to configure. But it doesn't work on my poor W95 tablet PC. -- Dave Cotton Directeur Linux Autrement 193 rue Marcel Cerdan 84270 Vedene 04 90 23 30 81 "Internet Sheriff Technology" revendeur en France <http://www.linuxautrement.com> IAX 17004902330

Hello all, Is X-lite soft phone support G.729 ? I actually use it but there is no G.729 support. Anyone know where to have it? Regards. Daniel. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050209/8cdbeeec/attachment.htm