similar to: cisco AS5300 : problem configuration

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

I'm experimenting (using for the first time) with using a cisco3620 to connect to the PSTN via a channelised E1 interface, with * handling all of the SIP calls. If anyone has any installation tips / help / documentation I would be most appreciative :) However, my first question is this: when I am in the setup, I see the following: Current interface summary Controller Timeslots

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

Hello, everyone. Right now, we are trying launch our own PBX system based on Asterisk(Fedora) with Cisco 2611. Cisco has 2 port FXO card installed on it. For testing, I have 2611 hooked into phone line with number of xxx-xxx-xxxx fine. (I'll call it F). Using softphone, I can dial in extension 1001 on asterisk, which should talk to cisco. After initial connection to Asterisk, I have try to

If you have a PRI terminated in a Cisco router talking SIP to * and would be willing to share your Cisco config, please respond. Also, I would be interested in knowing what version of IOS you are using. We are using an NM-HDV in a 3640. TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 236-5815

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

Guys. I need some advice on some h323 issues. I need to test connectivity from Asterisk to a Cisco AS5300 that has PSTN lines and to cisco 3600 voip routers. H323 needs to be used here but I was wondering if anybody has linked Asterisk to these Cisco routers before? Thank you for any pointers.

I see a lot of comments but no actual show runs. Can someone post a 7206 config. I am having a dickens of a time getting calls to pass. I currently have the following loaded. Cisco IOS Software, 7200 Software (C7200-IK9O3S-M), Version 12.3(8)T6, RELEASE SOFTWARE (fc2) Thanks !!! Jerry -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.344 /

Hi, I had previously posted about connecting an AS5300 to * via SIP/H323. I got it to work via SIP, but only 1 call at a time would work, and if a user from the * side hung up, the cisco would'nt catch the hangup. I an now trying to hook up to the cisco via E1, with a Sangoma A101 card in my * box. I would like it such that I call from * via E1/PRI to the cisco, and call out via R2 to

Hello all, When I generate an out-going call from *, the DTMF detection is not working ? ASTERISK --> GW AS5300 --> PSTN But the DTMF is working correctly when it's an incoming call. PSTN - -> GW AS5300 - -> ASTERISK Well, I tried with the 3 dtmfmode of asterisk inband, rfc2833 and info, no way !!! Is it normal that asterisk try to setup the outgoing-call using ULAW ? if I

I have 2610 XM with 1 Fastethernet and VIC2-2BRI. Dialin and dialout over pots is ok. Also inbound pots calls get redirected to Asterisk y.y.y.y So far so good. But I want to setup VOIP sessions with local carrier. I added dial-peer 40 for this. Session target x.x.x.x But calls will always get routed to the pstn peers 50 and 60. Peer x.x.x.x is never contacted or tried. My situation: PSTN

Hello, I'm trying to receive faxes with asterisk. My configuration is like this: PSTN fax -> ISDN -> Cisco router with VoIP module -> Asterisk When I try to send a fax from PSTN fax I got the standard fax signal, Asterisk starts rxfax application and then call ends and there is no tif anywhere. On the fax display there is still one message: Calling... Part of my extensions.conf:

Hi i am search a sample config (for asterisk and for cisco) for connect a cisco 1760 with a FXO card to my asterisk. Thanks for your help Jerome

Hello, I have an E100P, and in the zaptel.conf I have: span=1,1,0,ccs,hdb4,crc4,yellow fxsks=1-10 the light on the card is green( BTW what do all those states of the card that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or for the card?) in the asterisks` zapata.conf I have: [channels] context=default switchtype=euroisdn signalling=fxs_ks usecallerid=yes hidecallerid=no

I have the following configuration and am obviously missing something small that is causing * not to work as expected. I have the following defined in sip.conf [ccme-in] type=peer host=10.0.9.1 context=devel_in disallow=all allow=alaw nat=no canreinvite=yes qualify=yes and [devel_in] is defined in extentions.conf However when I try to call via the dial peer I have configured on the cisco

Hello, Has anyone experienced a segmentation fault in asterisk for using G729 against an AS5300 in SIP ? I'm having this problem. Also, any other codec I use gives me incompatible media (can be read in SIP DEBUG messages). AS5300 configured for multiple codecs, so is Asterisk. Tried G711u/A G723 and G.729. Any clues ? Regards, Jorge A. Info: Asterisk ver 1.0.7 stable Using AMPortal

All, I need to run this by everyone and see if someone has any idea's. I have a asterisk server setup and currently am receiving the inbound calling number where the name should be. My setup is.... One pri terminating into a Cisco 2431 router Sip messages from the Cisco get sent to a asterisk server linksys ata's a each remote end. I can receive the calling name if the call originates

Greetings, I am attempting to configure an AS5300 to provide a SIP based gateway to the PSTN from Asterisk. I have been unable to identify through the docs how specifically this should be configured in Asterisk and have not been able to get things working through trial and error. I am sure I am missing something fairly obvious here but any guidance (or example cfgs) would be much appreciated.

Hello, We have been working with the ReceiveFax application for some weeks now in order to receive faxes in T.38 and it works fairly well, but there are some faxes that for some reason we are not able to receive correctly. The asterisk version we are using is 1.6.0.6 with spandsp-0.0.5pre4 and the asterisk machine is behind a CISCO mediaGW to be able to communicate with the PSTN. The SIP call

I have several 7960 phones with SIP image (7.3) and Asterisk 1.0.1 on FreeBSD. When I have 2 active SIP calls on the 7960 phone there are no available lines for additional calls. I tried to configure 2 lines to the same SIP server but it's still limited to 2 calls. How to utilize all lines? -- Called user -- SIP/user-acc6 is ringing -- SIP/user-acc6 answered SIP/x.x.x.x-09a9a000 --