asterisk users - May 2005 - cisco 3620 setup (newbie cisco alert)

I'm experimenting (using for the first time) with using a cisco3620 to 
connect to the PSTN via a channelised E1 interface, with * handling all 
of the SIP calls.

If anyone has any installation tips / help / documentation I would be 
most appreciative :)

However, my first question is this: when I am in the setup, I see the 
following:

Current interface summary

Controller Timeslots D-Channel Configurable modes Status
E1 0/0     31        15        pri/channelized     Administratively up
E1 1/0     31        15        pri/channelized     Administratively up

I have set both controllers to hdb3, ccs with crc4

I notice that the D-Channel is set to 15. However, in the zaptel.conf 
file I use with my TE410p card, the D-Channel is set to 16. So, is cisco 
counting 0-14 (hence 15 is the D-Channek) and zaptel counting from 1-15 
(and therefore 16 is the D-channel) ? Or is my config wrong on the cisco 
or zaptel ??

Any help would be welcome. Thanks !

Julian

Your configuration is OK. Cisco is counting from 0, so  Serial 0:15 is 16th 
channel (D-channel) of first E1 (if you don`t have serial interfaces 
also...).
zaptel/asterisk is counting from 1, so 1-16 is D-channel of first E1 
interface.

See archive for thread named "Asterisk and Cisco AS5300 or 3600".
There is
example of configuration.

-b


----- Original Message ----- 
From: "Asterisk" <asterisk@dotr.com>
To: "Asterisk Users Mailing List - Non-Commercial Discussion" 
<asterisk-users@lists.digium.com>
Sent: Monday, May 16, 2005 2:18 PM
Subject: [Asterisk-Users] cisco 3620 setup (newbie cisco alert)

> I'm experimenting (using for the first time) with using a cisco3620 to 
> connect to the PSTN via a channelised E1 interface, with * handling all of 
> the SIP calls.
>
> If anyone has any installation tips / help / documentation I would be most 
> appreciative :)
>
> However, my first question is this: when I am in the setup, I see the 
> following:
>
> Current interface summary
>
> Controller Timeslots D-Channel Configurable modes Status
> E1 0/0     31        15        pri/channelized     Administratively up
> E1 1/0     31        15        pri/channelized     Administratively up
>
> I have set both controllers to hdb3, ccs with crc4
>
> I notice that the D-Channel is set to 15. However, in the zaptel.conf file 
> I use with my TE410p card, the D-Channel is set to 16. So, is cisco 
> counting 0-14 (hence 15 is the D-Channek) and zaptel counting from 1-15 
> (and therefore 16 is the D-channel) ? Or is my config wrong on the cisco 
> or zaptel ??
>
> Any help would be welcome. Thanks !
>
> Julian
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users@lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>

kurt x wrote:
>Since the 3620 has two slots it should be configured as follows:
>
>port <slot #>/0:D
>  
>
This gives me:

delta(config-dial-peer)#port 0/0:D
                                   ^
% Invalid input detected at '^' marker.

delta(config-dial-peer)#
>Kurt
>
>
>  
>

I can`t see voice-port in your configuration. Something like this:

!
voice-port 1/0:15            ; voice-port 1/0:15, if your D channel is 
Serial1/0:15
 input gain -6
 output attenuation 14
 echo-cancel coverage 32
 echo-cancel suppressor
 cptone SK
 description E1
 bearer-cap Speech
!

If you configure voice-port, try again to configure dial-peer (port x/y:15 
command) and if you have DSPs in you box, you must see something like this:

SIP-3640#show voice dsp

DSP  DSP             DSPWARE CURR  BOOT                         PAK 
TX/RX
TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK 
COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== 
===========C549 000 00 {high}    3.4.56 IDLE  idle      0  0 2/0:15    01     0 
0/16
         01 {high}    3.4.56 IDLE  idle         0 2/0:15    17     0 
0/0
C549 001 00 {high}    3.4.56 IDLE  idle      0  0 2/0:15    02     0 
0/16
         01 {high}    3.4.56 IDLE  idle         0 2/0:15    18     0 
0/0
....

If you don`t have any DSP in your C3620, it will be unusable. So check it!

-b


> Many thanks for your help: Details are as follows:
>
> ================ Show voice dsp ====================> delta#show voice
dsp
>
> DSP  DSP             DSPWARE CURR  BOOT                         PAK 
> TX/RX
> TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK 
> COUNT
> ==== === == ======== ======= ===== ======= === == ========= == ===== 
> ===========>
> delta#
>
> ================ Show ver ======================> delta#show ver
> Cisco Internetwork Operating System Software
> IOS (tm) 3600 Software (C3620-J1S3-M), Version 12.3(13a), RELEASE SOFTWARE 
> (fc2)
> Technical Support: http://www.cisco.com/techsupport
> Copyright (c) 1986-2005 by cisco Systems, Inc.
> Compiled Tue 26-Apr-05 09:12 by ssearch
> Image text-base: 0x60008B00, data-base: 0x619C0000
>
> ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE 
> SOFTWARE (fc1)
> ROM: 3600 Software (C3620-J1S3-M), Version 12.3(13a), RELEASE SOFTWARE 
> (fc2)
>
> delta uptime is 2 hours, 57 minutes
> System returned to ROM by power-on
> System image file is "flash:c3620-j1s3-mz.123-13a.bin"
>
> cisco 3620 (R4700) processor (revision 0x81) with 58368K/7168K bytes of 
> memory.
> Processor board ID 24364331
> R4700 CPU at 80MHz, Implementation 33, Rev 1.0
> Channelized E1, Version 1.0.
> Bridging software.
> X.25 software, Version 3.0.0.
> TN3270 Emulation software.
> Primary Rate ISDN software, Version 1.1.
> 2 Ethernet/IEEE 802.3 interface(s)
> 32 Serial network interface(s)
> 2 Channelized E1/PRI port(s)
> DRAM configuration is 32 bits wide with parity disabled.
> 29K bytes of non-volatile configuration memory.
> 24576K bytes of processor board System flash (Read/Write)
>
> Configuration register is 0x2102
>
> delta#
> ================= Show inte desc ======================> delta#show inte
desc
> Interface                      Status         Protocol Description
> Et0/0                          up             up       connected to 
> CorporateNetwork
> Se0/0:0                        admin down     down
> Et0/1                          admin down     down
> Se1/0:0                        down           down
> Se1/0:1                        down           down
> Se1/0:2                        down           down
> Se1/0:3                        down           down
> Se1/0:4                        down           down
> Se1/0:5                        down           down
> Se1/0:6                        down           down
> Se1/0:7                        down           down
> Se1/0:8                        down           down
> Se1/0:9                        down           down
> Se1/0:10                       down           down
> Se1/0:11                       down           down
> Se1/0:12                       down           down
> Se1/0:13                       down           down
> Se1/0:14                       down           down
> Se1/0:15                       down           down
> Se1/0:16                       down           down
> Se1/0:17                       down           down
> Se1/0:18                       down           down
> Se1/0:19                       down           down
> Se1/0:20                       down           down
> Se1/0:21                       down           down
> Se1/0:22                       down           down
> Se1/0:23                       down           down
> Se1/0:24                       down           down
> Se1/0:25                       down           down
> Se1/0:26                       down           down
> Se1/0:27                       down           down
> Se1/0:28                       down           down
> Se1/0:29                       down           down
> Se1/0:30                       down           down
> Di0                            up             up
> delta#
>
> ============= show running-config ===================> delta#show
running-config
> Building configuration...
>
> Current configuration : 1996 bytes
> !
> version 12.3
> service timestamps debug uptime
> service timestamps log uptime
> service password-encryption
> !
> hostname delta
> !
> boot-start-marker
> boot-end-marker
> !
> enable secret 5 #########################
> enable password 7 ##########################
> !
> clock timezone GMT 0
> no aaa new-model
> ip subnet-zero
> no ip routing
> !
> !
> ip name-server 192.168.1.10
> !
> no ip cef
> ip dhcp-server 192.168.1.10
> isdn switch-type primary-net5
> isdn voice-call-failure 0
> !
> !
> !
> voice class codec 3
> codec preference 1 g711alaw
> codec preference 2 g711ulaw
> !
> !
> !
> !
> !
> !
> !
> !
> !
> username admin privilege 15 password 7 ##################
> username jmls privilege 15 password 7 ###################
> !
> !
> controller E1 0/0
> channel-group 0 timeslots 1-31
> !
> controller E1 1/0
> pri-group timeslots 1-31
> !
> !
> !
> interface Ethernet0/0
> description connected to CorporateNetwork
> ip address 192.168.1.11 255.255.255.0
> no ip route-cache
> no ip mroute-cache
> half-duplex
> no mop enabled
> !
> interface Serial0/0:0
> no ip address
> no ip route-cache
> shutdown
> !
> interface Ethernet0/1
> no ip address
> no ip route-cache
> no ip mroute-cache
> shutdown
> half-duplex
> !
> interface Serial1/0:15
> no ip address
> no ip route-cache
> isdn switch-type primary-net5
> no cdp enable
> !
> interface Dialer0
> no ip address
> !
> no ip http server
> ip classless
> !
> !
> dialer-list 1 protocol ip permit
> dialer-list 1 protocol ipx permit
> !
> !
> !
> !
> !
> dial-peer voice 1000 voip
> application session
> destination-pattern .T
> voice-class codec 3
> session protocol sipv2
> session target ipv4:90.0.0.33
> session transport udp
> dtmf-relay rtp-nte
> !
> dial-peer voice 100 pots
> application session
> max-conn 30
> destination-pattern 0..........
> translate-outgoing called 1
> no digit-strip
> direct-inward-dial
> forward-digits all
> !
> sip-ua
> retry invite 4
> retry response 3
> retry bye 2
> retry cancel 2
> sip-server ipv4:192.168.1.20
> !
> !
> telephony-service
> !
> !
> line con 0
> exec-timeout 0 0
> password 7 ###############
> login
> line aux 0
> line vty 0 4
> password 7 ####################
> login
> !
> !
> end
>
> delta#
>
> Julian.
>
> barney wrote:
>
>> Wow :-) . Ok, try to send whole running-config from your router and
also
>> send me output from commands: "show ver", "show voice
dsp" and "show inte
>> desc"
>>
>> -b
>>
>> ----- Original Message ----- From: "Asterisk"
<asterisk@dotr.com>
>> To: "Asterisk Users Mailing List - Non-Commercial Discussion"
>> <asterisk-users@lists.digium.com>
>> Sent: Tuesday, May 17, 2005 12:23 PM
>> Subject: Re: [Asterisk-Users] Re: cisco 3620 setup (newbie cisco alert)
>>
>>
>>> The "^" marker appeared under the "o" in
"port", the email changed the
>>> position :(
>>>
>>> So it seems as if the "port" command in missing.
>>>
>>> delta(config-dial-peer)#port ?
>>> % Unrecognized command
>>> delta(config-dial-peer)#port
>>>
>>> Julian
>>>
>>> barney wrote:
>>
>>
>
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users@lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>