similar to: E1 Card Signaling

Hi list, There's any E1 card I can use with Asterisk that support R2 signaling? Digium's E1400P doen's support it, right? thanks in advance Eduardo

Hello everyone. I am looking for a E1 PRI card which supports network side signaling not CPE. The main idea is to connect an plain old E1 compliant PBX which doesn't have an VoIP module to the newly created VoIP infrastructure. Could we use a Digium TE122P or something other to resolve this situation? Thanks in advance. Dimitar -------------- next part -------------- An HTML attachment was

Hi all, My name is Ricardo and unfortunately I'm just crawling in this telecomm/asterisk world. So, after reading all day long i still don't understand a few things. :D I'm trying to "develop" a call recorder for a costumer. He has a small call center ( 10 agents ) and want to record all calls. Since he already has everything (ACD only) working perfectly in the PBX and

Anyone configured a E1 PRI in Kuala Lampur, Malaysia with TM Malaysia? What signaling did they provide, framing, formatting? primary-4ess Lucent 4ESS switch type for the U.S. primary-5ess Lucent 5ESS switch type for the U.S. primary-dms100 Northern Telecom DMS-100 switch type for the U.S. primary-dpnss DPNSS switch type for Europe primary-net5 NET5 switch type for UK,

Hello Folks, I'm trying to decide here between a few cards for connecting an Asterisk box to a single E1 channel (either PRI or R2 signaling): - Digium E100P: has been replaced by the TE110P below, but can still be had at places like digitnetworks.com for $475, and I guess there's always a place for good-olde-obsolete cards in the world as long as they work :-) - Digium TE110P:

Hullo everyone, Iam new to Asterix but am trying to get R2 signalling working with a Digium E100P E1/PRA Card. My Telecom doesn't have an implementation of ISDN PRI yet, so it's R2 that is supported. Could anyone have a patch to fix this for me. Am told it has something to do with Assembly Language programming. Please help me fix this. Regards, Nicholas

Dear all I have setup with mediant 2000 with avaya now i want to install E1/PRI card with asterisk and trunk with E1 with Avaya E1 port so i want to buy E1 card for asterisk so which card is best and cast effective for my setup i want 1 port E1 card so can you suggest me which card is best for my setup and i want QSIG singaling with avaya Regards satish patel

Dear all I have asterisk 1.2 and now i want to install E1 card with support Q.SIG singaling so which E1 card is best for my setup i need single port E1/PRI card which support Q.SIG Regards Satish patel --------------------------------- Take the Internet to Go: Yahoo!Go puts the Internet in your pocket: mail, news, photos & more. -------------- next

Hola! I've a Digium E1 card, zaptel recognizes it as (loading the module with debug=1) Setting up DMA (write/read = 321b2000/321b2200) Controller version: 43 Framer: DS21554, Revision: 5 (E1) Found a Wildcard: Digium Wildcard E100P E1/PRA Using CCS/HDB3 coding/framing with CRC4 120 Ohms Calling startup (flags is 4099) Started DMA Got interrupt: 0x0005 /etc/zaptel.conf:

Hi Team, i have been facing issues with sangoma card with 16 E1. used LibSS7 asterisk 1.6 with 8 E1 the links are stable , but moment i add another card of 8 E1 for to support 16 E1. link keeps fluctuating any idea why ? Please help Thanks Vinod Dharashive -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

Hi Sangoma a104 card have in product specyfication support for Line protocol SS7 , http://www.sangoma.com/products/p_aft-104-specs.htm [..] Line protocols Frame Relay, X.25, HDLC, PPP, SS7, Transparent bit-stream, BSC. [..] Anyone of you guys use line protocol SS7 for E1/T1 termination in asterisk ? As far I know asterisk don't have support for SS7 signaling, but my telco wants to setup

Hello All, Does anyone know of a software emulator that can be used to simulate hardware such as an E1? I need to play with AstUnicall in a test environment and don't have access to these circuits from the US. If there is an alternate way to test/play with AstUnicall, please let me know! Thanks, Mark -------------- next part -------------- An HTML attachment was scrubbed...

Hello list, (Resending this email due to a typo in previous copy) I need to do E1 to T1 conversion for a project, and was wondering if there exists a card with both E1 and T1 on it. Or is it possible to use two separate cards in an asterisk box, one for E1 and one for T1? (Please don't mention aculab or adtran, dealt with them in the past, won't deal again.) I talked to Digium and the

Roberto estoy en uruguay en estoos momentos. Recien lllego el miercoles El mar 31, 2013 1:59 p.m., <asterisk-users-request at lists.digium.com> escribi?: > Send asterisk-users mailing list submissions to > asterisk-users at lists.digium.com > > To subscribe or unsubscribe via the World Wide Web, visit > http://lists.digium.com/mailman/listinfo/asterisk-users

Hello list, I need to do E1 to T1 conversion for a project, and was wondering if there exists a card with both E1 and T1 on it. Or is it possible to use two separate cards in an asterisk box, one for E1 and one for T1? (Please don't mention aculab or adtran) Zeeshan A Zakaria -- www.ilovetovoip.com www.pbxforall.com (beta) -------------- next part -------------- An HTML attachment was

> Hi Gareth Blades & Doug, > > Thanks so much for for the feedback. I have searched on lot of documents > but couldn't able to find clear answer regarding it. > > I hope you guys replies are very much help all in aterisk community. > > > Thanks & Regards, > > Vidura Senadeera, > > Network Engineer, > > Debug Solutions > > Sri Lanka .

hello, We encountered signaling problem with a french national carrier. They ask us, which signaling is configured on our single E1. I need to know if it's ETSI, VN4 or VN6. I know what ccs, and hdb3 mean but I do not succeed to make the link between the signaling type. I searched through RFC Q.921 and Q.931 It would be great to obtain some help. cedric