similar to: ztdummy loading: unable to specify channel 1

Upon setting up and configuring the my extension.conf, meetme.conf and following the instruction outlined at this web page: http://www.voip-info.org/wiki-Asterisk+timer+ztdummy I get the following errors when calling the meetme number. Executing Wait("SIP/216.53.118.2-f41196e0", "1") in new stack -- Executing MeetMe("SIP/216.53.118.2-f41196e0",

Hi, I have two WCT100P cards installed on a suse 9.0 box. Installation for Zaptel complains of some unresolved dependencies. The zaptel and wct1xxp modules load without any errors. ztcfg give no problems. The problem is when I start asterisk I get the following error and asterisk shuts down

After emerging some updates this morning asterisk 1.0.3 fails to start I get the following errors: ..Jan 6 00:39:24 WARNING[28998]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Jan 6 00:39:24 ERROR[28998]: chan_zap.c:6197 mkintf: Unable to open channel 1: No such device or address here = 0, tmp->channel = 1, channel = 1 Jan 6 00:39:24 ERROR[28998]:

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hi, all I have installed TDM400 card. I can see it is there (lspci). But Asterisk does not find it. phonebox2*CLI> zap show status No Zaptel interface found. I assume that driver is not loaded, but I am sure I have installed it (I compiled zaptel and then re-build asterisk and did make install for both zaptel and asterisk). When asterisk is started I get: Jan 2 06:28:08 WARNING[3473]:

Hello, This is debug output I get: Jul 28 15:05:49 WARNING[8249]: chan_oss.c:239 sound_thread: Read error on sound device: Resource temporarily unavailable [chan_zap.so] => (Zapata Telephony w/PRI) Jul 28 15:05:49 WARNING[8249]: chan_zap.c:924 zt_open: Unable to specify channel 1: No such device or address Jul 28 15:05:49 ERROR[8249]: chan_zap.c:6460 mkintf: Unable to open

can somebody that has these hardwares(X101P and S400P) working on his asterisk system please assist.................. you can send the solution to austino@skannet.com..... the error message is what i have below. ---------- Forwarded message ---------- Date: Thu, 1 May 2003 21:01:21 +0100 (WAT) From: austino@skannet.com To: asterisk-user@lists.digium.com Subject: Error working with X101P and

Of course I am not a kernel expert, so .. please be patient. I am investigating on my zaptel/zapata problem. As the main error message asterisk quits on mentions <'/dev/zap/channel': No such file or directory> I went peeking over there. [Asterisk Verbose Error Mar 13 20:43:35 WARNING[5779]: chan_zap.c:763 zt_open: Unable to open '/ dev/zap/channel': No such file or

Im getting the following error when I try to start Asterisk WARNING[16384]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Nov 29 21:40:43 ERROR[16384]: chan_zap.c:6195 mkintf: Unable to open channel 1: No such device or address I'm using a TDM22B card. ============= # Zaptel Configuration File # loadzone=us defaultzone=us fxoks=1-2 fxsks=3-4 ==============

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi List, I have a test asterisk box with a TDM400P with 4 FXO modules plugged in. Yesterday I could use the box without any issues - no problems. This morning, the sound on the box was absolutely horrible. After some fiddling about, I have rebooted the box, and now asterisk refuses to start! Here's the message I get: Jun 9 10:45:53 WARNING[3297]: chan_zap.c:769 zt_open: Unable to

Hi all, I have a problem starting the ztdummy. Here is what happens: [root@asterisk /]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy After this, ztdummy is visible with lsmod, but when I try MeetMe, I get following: == Parsing

Hello, I am posting this after spending hours digging through the list archives. Problem : When asteirsk plays a voice prompt, the voice clip is really choppy. I figure that this is something to with the sound card, the timing of playback etc. But cannot seems to find an answer. Here is the Notice which appear when voice prompt is played. NOTICE[1217602880]: File sched.c, Line 209

Im trying to install and configure sangoma ... every thing is OK but when type the command "wanrouter start" the following error apears: wan Driver not found. Thanks for any help

Any suggestions would be great. No config files changed. I have been trying the latest cvs every few days for a few weeks now. I currently am using 06/06/2003. [root@pbx asterisk]# asterisk -c Asterisk CVS-08/07/03-15:43:33, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net>

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

I'm having a problem defining my channels Here is my zapata.conf ----------------------------------------------------------------------------------------------------- ; Zapata telephony interface ; ; Configuration file [channels] ; rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes

Greetings all, I've just put two X100P cards to my box and despite trying everything I can find on the web, I can't get the second one to work. I've edited /etc/modules.conf so that ztcfg doesn't run automatically. To start, I run: /sbin/modprobe zaptel /sbin/modprobe wcfxo /sbin/ztcfg /sbin/modprobe ixj and ztcfg says: ZT_CHANCONFIG failed on channel 2: No such device or

All of sudden my FXS module is not working. I have a TDM card with one FXS and one FXO, FXO module seems working fine. I also noticed the LED is not on for my FXS module while it is on for my FXO module. Sep 13 12:11:44 WARNING[9870]: chan_zap.c:887 zt_open: Unable to specify channel 1: No such device Sep 13 12:11:44 ERROR[9870]: chan_zap.c:6612 mkintf: Unable to open channel 1: No such device