similar to: E1 in Brazil

Hi everybody,, I need to block incoming collect calls to my Asterisk box but I could not find out where to do that. Went to zaptel.h but I did not see any timing which can be applied to collect calls. Does anybody knows if I can set this up in Asterisk? I'm using an E100P connected to the PSTN and a T100P connected to a Zhone 100. Version: Asterisk CVS-05/30/04-16:28:04 thank you Oz

Hi, We currently have an Asterisk box (P4 2.4 Ghz, 512Mb RAM, 1 T100P, Zhone Channel Bank and 1 E100P) connected to an ISDN running without any problems. That machine is working for about 1 year. Two days ago, we decided to switch that machine for two PowerEdge 600SC (HA) and we got some problems. The running machine (P4 2.4Ghz) has an Intel motherboard with four 32-bit 3.3v PCI slots,

Hi. I'm getting new lines for using with Asterisk. In my Telco they said I could choose between Analogic lines and RDSI lines... I've already bought a TDM400P with FXO modules. Can you give some hints on the differences between RDSI and normal Analogic lines? Would I have problems for using a RDSI line with the TDM? Any other issue in general? Thanks in advance, RODOLFO --- avast!

Hello, I am trying to see what I need to do SIP to H323 using G.729. I have Oh323 and SIP working with G711 fine. If I have a SIP client configured to use G729 and H323 client also to G729, how many license should I need to buy from Digium. Many thanks SW

Hello guys, I have this problem when a call is received in my PBX: (Caller) --> (Redirecting Service) --> (E1 PRI) --> (Asterisk PBX) --> (Internal Phone) Reception works fine, but when conversation finishes and the agent at internal phone hangs up, the call at caller's side is still alive for many seconds until it hangs up. The problem is that Telephone Company is billing me

Hi, Does anybody have ATA 188 working with any kind of fax machine? I've tried many different configuration following the Cisco Online Manual and I couldn't get this working with Asterisk. I were trying do change the ATA Connect Mode and Audio Mode reading the (http://www.cisco.com/en/US/products/hw/gatecont/ps514/ products_configuration_example09186a00800d698e.shtml) and allowing

Hey All, I need to forward an extension to an other depending on the current time but I could not get it done with GotoIfTime. What I'm trying to do is ring on the extension 1 if time is between 8:00AM and 2:00PM and on extension 2 if is between 2:01PM 11:00PM. exten => 111,1,GotoIfTime(8:00-14:00|*|*|1-12?333) exten => 111,2,Dial(${Person1}) exten => 111,3,Dial(Hangup) exten

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

hi guys, I have a little problem maybe you can help ... I have an asterisk setup, with an E100P, and an ISDN-PRI 30 channel line from the telco going into it .. the E1 line is OK, because plugged into a Lucent Portmaster 4 it works OK .. plugged into the asterisk box I just get an engaged tone, and asterisk posts this message on screen : WARNING[1167272000]: File chan_zap.c, Line 5275

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

I've got a * box with a TDM40B and an E100P. The E1 is connected to a Shout900 VoIP gateway from net.com. My question is, when I place a call from an analog phone and that call is routed over the E1, what encoding is used? And do I have any control over that? I'm obviously not an expert here, but the Shout900 vendor is claiming that some difficulties that we are having with integration are

All- I'm attempting to set up a Sipura SPA-3000 in Sao Paolo, Brazil. Not being a portuguese speaker, I'm having a rough time of finding the relevant information on how to make the thing pick up the PSTN line and make an outbound call. The sipura in question works fine on a bench connected to a POTS line in the US, but is now plugged in in Sao Paolo. The immediate thing I notice is that

Hi, I apologize for a portuguese message at this group, but I am trying to reach brazilians who read this great group. It''s about the release of the first Ruby on Rails book for the brazilian audience. Here it goes: Galera, finalmente terminei de escrever o livro e entreguei o material para a editora esta semana, agora resta esperar at? que eles nos digam quando ser? a data do

All- I am considering an Asterisk implementation in Brazil. Unfortunately, this presents something of a challenge to plan sitting in Chicago, USA. I know there is a large section of Brazillian Asterisk users who actively read this list- so I'd love to pump out a few questions- note, I'm not necessarily a newbie, having successfully implemented a few Asterisk boxes here in the US. My

Hello Folks, I'm trying to decide here between a few cards for connecting an Asterisk box to a single E1 channel (either PRI or R2 signaling): - Digium E100P: has been replaced by the TE110P below, but can still be had at places like digitnetworks.com for $475, and I guess there's always a place for good-olde-obsolete cards in the world as long as they work :-) - Digium TE110P:

We are not having any luck with the E100p card here in Australia, it will work with a crossover cable to another device but will not talk to our Telco Telstra who probably have a weird implementation of an E1. Any suggestions on a replacement? Regards Mark McKibbin DCS Internet 64 Queen St Warragul Victoria 3820 Australia www.dcsi.net.au mark@team.dcsi.net.au Ph. 1300 665575 Fx. 1300 556595

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Hullo everyone, Iam new to Asterix but am trying to get R2 signalling working with a Digium E100P E1/PRA Card. My Telecom doesn't have an implementation of ISDN PRI yet, so it's R2 that is supported. Could anyone have a patch to fix this for me. Am told it has something to do with Assembly Language programming. Please help me fix this. Regards, Nicholas