similar to: TDM400P question.

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hi to all, I have been using Wildcard TDM400P with four fxs modules and it was working fine now I have added another Wildcard TDM400P with four fxs modules . So there are total 8 ports for 8 hard phones. I have modified following configurations In /etc/zaptel.conf loadzone=us defaultzone=us fxoks=1-8 in /etc/asterisk/zapata.conf context=headoffice signalling = fxo_ks

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Hi All, I'm attempting to use two X100P cards and one TDM400P card. What driver do I load for the TDM400P? Is their any documentation for this card yet? Also, I know this has come up before but I can't seem to find it in the archieve... how do I configure the second X100P card? Anyone have a working sample? Thanks in advance, Randy

Hi, I am having some trouble getting a TDM400P working, and would be very appriciative of some ideas. I have installed a TDM400P, and downloaded the appropriate files from CVS, compiled, installed and modprobe'd the devices.

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Hello, I thought that my Digium TDM400P would be the right hardware to support the zaptel timer, and put the following IAX.CONF entry to test, (trunk=yes) in the example below [VHAX] type=peer auth=md5 username=whoknows jitterbuffer=yes ;trunk=yes secret=terriblesecret host=4.5.6.7 qualify=1200 disallow=all allow=ulaw allow=gsm ;allow=g711u ;allow=g711a But, it didn't work. So I had to

Can anyone suggest where I might begin looking for an answer please? I have just installed a TDM400P (2x FXS and 1x FXO modules installed) The first problem is that it does not seem to be able to detect if the remote party has hung up when a call comes through on the FXO. For example, if someone calls in, and then hangs up at any time after it starts ringing, Asterisk carries on as though the

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

Hi I have a Dell PE2300 with a Digium TDM400P line card in it (with one module to handle an inbound phone line). This is running on a Fedora 8 system with Asterisk 1.4.21.2-1.fc8 This system has been working nicely for about 12 months. After a recent move of office and relocation of the server Asterisk is back on line, but the TDM line card has stopped working. I have spent half a day

Hello, everyone After having spent several time to look for any solution for my problem, I decided to write here. Here is the problem got a Digium X101 FXO card and Digium TDM400P alias freshmaker (1 fxs module on it on first port ) in my asterisk box. The X101 works perfectly. The problem comes from the TDM400, when i plug a tested working phone on it , i get no dialtone; the goal is to

Hi, I bought the Digium Asterisk Developers kit a few weeks ago, got the x101p and a tdm400p cards, both seemed to be working fine up until today, now the tdm400p seems to have gone to the great PBX in the sky ...... If I left the reciever on the analog phone I don't get a dial tone and nothing appears on the asterisk console, If I use my cellphone and dial in I see Asterisk Ready.

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

Hi all, I have just purchased the DevKit from Digium and received a X100P and a TDM400P (it has one FXS module). The problem is that I can't get the kernel module (wcfxs) to load and run. I have searched the archives and can't find anything about this. Do the messages below ring any bells with anyone ? There is no interrupt clash (see pci list below). I am running on a AMD 1.2G

hi guys, i got a TDM400P FXS card an everything is fine except for this when i do modprobe wcfxs , the linux shows 2 TigerJet Network Inc Model 300 128k. i don't know why it is showing 2 of them. or is that what it is? ERROR: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 0 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 0 cshould be