similar to: Skinny + XMLDefault

> thanks, using your example, and this url: > http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note0 9186a00800dea82.shtml <http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note 09186a00800dea82.shtml> > I got it to work... then I realized that there's no way the SIP phone > on asterisk is going to get the MWI ( message waiting

>how does the phone know where to find the TFTP server..? Dude, option 150 in your DHCP server: http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186 a00800942f4.shtml We use the same option for our Mitel phones. HTH.

Hi, I'm after two very specific ringtones for the 79xx's... A dog barking, and a horse either galloping or neighing. I've tried making the sounds, but for some bizarre reason they're not working. I used to make quite a few ringtones for the 79xx's, but I seem to have forgotten how to do it! And to top things off, I can't even find the documentation on Cisco's site

Hi Everyone - I just got my hands on a Cisco 7970 and was told that I should do a factory reset before trying to configure it to work with Asterisk. After the factory reset, it will not boot at all, instead sits with the line button lights flashing one at a time in sequence. I have had no luck trying to figure it out - anyone run into the same problem that can lend a hand..? Thanks

Hello List, Does anyone have access to the soft key configuration files for the Cisco 7911/7941/7970/7971 phones? Checked up on the Cisco site and didn't find much up there. Thanks Roy Anciso Director of Technology Manistee Intermediate School District 1710 Merkey Road Manistee, MI 49660 Ph: 231-723-4264 Fx: 231-723-1690 roy at manistee.org -------------- next part

There was a thread a few months ago that tossed around some ideas for using a cisco phone for intercom or paging. I don't have any ip phones, and wondered if anyone had any luck getting intercom or paging to work on the cisco units. Do any of the (cheaper) ip phones have a way to support intercom or paging? I presume that it's not part of the SIP or IAX protocols. Chris.

hi! i had some good news regarding the cisco 7920 and the internetworking with asterisk (and possibly SIP ?). Status: chan_sccp.so not coredumping anymore :-) Phone contantly in reboot loop [see below] :-( Reboot Loop means: ------------------ Phone auth's with AP Phone gets IP from DHCP & TFTP Server Phone loads OS7920.TXT Phone loads SEP<macaddr>.CNF.XML Phone loads

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

I have 4 7960's that I am trying to get working but 2 of them will not update to the SIP image on my tftp server like the first ones did. i keep getting the error on the phone 'Defaulting CM to TFTP server' like it isn't seeing the *.bin on the server. are you supposed to have on of those for each phone? would be like cisco et al to do something like that. TIA Jason Kawakami

Hi, please tell me, is original skinny support in Asterisk stil under development or is better to try chan_sccp from http://chan-sccp.sourceforge.net ? my first try was unsuccessfull (chan_sccp compile OK, but module loading fail during Asterisk startup) and my phone (C7940) seems to be not supported in original chan_skinny :( PJ

Hi All I'm trying to get my 7970 working on the latest head version of Asterisk without success, perhaps someone could help. I'm using the head version of Asterisk with the chan_sccp from berlios.de dated 7th August. The compilation of chan_sccp seems to have worked without any problem, however I'm pretty sure the problem I have is with the config files in TFTPBOOT:- With the 7970

Evnin' (o; As chan_sccp is pretty much dead, doesn't compile on FBSD anyway and isn't supported on * 1.4.x I tried going with chan_skinny... The Cisco 7970 registers and is being acknowledged by * but that's it... I see no lines on the 7970 display configured and it is not reachable or it can't make any outboudn calls... The docs are pretty non-existent for skinny and the

Hi! I'm trying to communicate a Cisco CCM 4.0 with Asterisk 1.2.11, I 've followed the info in http://www.voip-info.org/tiki-index.php?page=Asterisk+Cisco+CallManager+Integration but still not able to make Asterisk communicate with Cisco. I keep on receiving --- SIP/2.0 400 Bad Request - 'Malformed/Missing URL' --- and --- SIP/2.0 404 Not Found --- messages

It can be done. 1. Setup a new Vm profile on CCM with a mask of XXXX 2. Setup a CTI route point: a. Set the directory number to a pattern. I use *27XX but any pattern that you can send from * is good, ie. 88XXX b. Set the VM profile to the newly created profile c. Set the line to forward all calls to VM 3. Change the dialplan in * to append the extension called to the

Hi all, I'm writing my graduation theses : analysis VO-IP protocols , and I cannot find any documents about Cisko Skinny Client Control Protocol. I have Cisco CallManager and some IP-phone and I'm sniffing traffic between that, but I don't understand, how this protocol works. Clearly i'm looking for description of SCCP commands and explanation some basic SCCP scenarios or what

I have asterisk 1.09 running with chan_sccp.20050701 on Fedora core 4 with kernel 2.6.12. I have a Cisco 7940 working with X-lite working on XP too, connecting to each other, Asterisk and FWD. The 7940 upgraded to SIP7.4 with xmlDefault.cnf.XML getting delivered via tftp using the loadInformation8 parameter method taken from voip-info.org ("Configuring Cisco 79xx phones with Asterisk"

Hi there! Has anyone succesfully used a Cisco 12 SP+ with *? If so, how did you do? I'v not even tried, but before trying I thought I could bug you somewhat. =) //Filip

2 new Cisco 7960 phones are requesting a CTLSEP file, seems like I triggered the universal application loader. I want to load the sip image 7.2 According to this Cisco information: http://www.cisco.com/en/US/customer/products/sw/voicesw/ps4967/products_upgr ade_guides09186a008022a968.html#wp1047292 If the CTLSEP MAC file is not present or is empty, the phone proceeds in nonsecure mode with the

Hi! How can I install Media Player 7.1 under wine? I don't have a windows partition, and I cannot install internet explorer, because the install of IE5 crashes either. regards, -- Alex [jali0@t-online.de]

Dear all, I would like to solve the following problem, which can be done with optimal control theory or dynamic programming: max(x,y) a*u1+b*u2+c*f1(u2) s.t. 0<u1<x, 0<u2<f2(x,u2), x'=f3(u1,u2,x) which can be rewritten if optimal control theory should be applied as H=a*u1+b*u2+c*f1(u2)+lambda*(x') s.t. 0<u1<x, 0<u2<f2(x,u2) The maximum principle