similar to: tdm40b

Hi list, I'm trying to set up a TDM40B, but modprobe returns the fowling errors: asterisk:~# modprobe wcfxs ZT_CHANCONFIG failed on channel 1: Invalid argument (22) /lib/modules/2.4.18/misc/wcfxs.o: post-install wcfxs failed /lib/modules/2.4.18/misc/wcfxs.o: insmod wcfxs failed Could someone give me a help? Thanks in advance Eduardo

Here is my system: POWER SUPPLY 450W ALLIED ATX450P4 R(41) MB NFORCE2 A7N8X DELUXE ASUS RTL(Standard) CPU AMD|2500/333 ATHLON XP BARTON R(Standard) DDRAM 256M|DDR333 PC-2700 -K %(Standard) HD 40GB|WD 7200RPM 8MB WD400JB%(70) VGA ASUS|V8170MAGICII/T 64M MX440SE(58) CD ROM 56X|AOPEN CD-956 RTL(22) Besides the above parts, i have 2 X100P FXO PCI cards, and 1 TDM40B I bought 2 phones from radio

I have problem with a TDM40B installation. When i modprobe wcfxs the error i get is the following: /lib/modules/2.4.19-4GB/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.19-4GB/misc/wcfxs.o: insmod

Hi everyone, Sorry for forwarding and top-posting this email again but its as if my TDM40b has keeled over yesterday. After a few hours last night and swapping the card to another asterisk server (with exactly the same result) I needed to have the FXS ports working ASAP this morning so I have repaced the functionality of the TDM40b with some Grandstream handytones which I already had in

I have just a second case where after * had been up for a few weeks working perfectly, it suddenly stopped talking to all the extensions. The I4L was still working perfectly though... I tried to stop asterisk, rmmod the modules, and insmod, and re-start asterisk but it did this: Using /lib/modules/2.4.21-pre5/misc/zaptel.o Using /lib/modules/2.4.21-pre5/misc/wcfxo.o Using

I have problem with a TDM40B installation. When i modprobe wcfxs the error i get is the following: /lib/modules/2.4.19-4GB/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.19-4GB/misc/wcfxs.o: insmod

OK, I have a Asterisk @ Home 1.0.7 server with two Digium TDM400 cards, one 4 port FXO and one 4 port FXS. When I plug an analog cordless phone into the TDM40B card and setup a ZAP extension, the phone rings in and you can answer just fine. The weird part is when you try to get dialtone from the cordless handset it rings all of the other extensions... One other thing to mention is that the

Hi ! I have a TDM40B and i try to use it connected to modem for incoming call data transfert. I have no problem to use it with a phone and a talk communication work fine. But when we try to use with modem, with most modem, we got data carrier for few seconds and channel hungup. < [ TYPE: Null Frame (4) SUBCLASS: N/A (3) ] [Zap/4-1] -- Zap/4-1 is ringing << [ TYPE: Null Frame

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hi, I recently purchased two X100Ps and a TMD40B. I have set everything up according to the instructions however I can't get asterisk to pick up an incoming call (It just keeps ringing). Also, when I pick up an internal extension I get dead air. I searched the mailing list for 3+ hours -- What am I missing? Thanks in advance for your help. Here are the installion steps that I used:

We are using TDM40B's to connect some devices to Asterisk which depend on caller information arriving as ANI, rather than as Caller ID. I am unsure if the TDM40B supports this in the first place, and if so, I am unsure how to configure it so. I've searched the wiki but couldn't find anything. Can someone please confirm whether or not this is possible? As a fallback I could reconfigure

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

Firstly, the problem... Ever since I installed and setup asterisk, I have had various problems, initially it was echo caused by the ISDN (isdn4linux) card I was using. So, I upgraded to the X101P from digium. I still had echo, so I figured it was also caused by the ATA186 (cisco) I was using. So, I upgraded again to the TDM40B quad FXS card. This solved pretty much all my problems, except

Hi all, Does anyone run Asterisk on FC4? with Digium's TDM40B cards. any success stories? my Intel 865 M'd+ Intel 3.0GHz freezee during installation (FC4). Please any comments? Kumara

Hi. I was testing my brand new TDM40B and noticed that when the kernel module is loaded (so the card is powered on), the chip onto the ringer module (the one below the S/N label) is pretty hot (I can't touch it for more than 2 seconds). Is that normal ? Or too much hot could be dangerous ? Matteo Matteo Brancaleoni Espia - Emmegi Sys Admin http://www.espia.it

Hi, I get the following message when I try to run Asterisk. This happened after I changed some of the configuration files: extensions.conf, zaptel.conf and zapata.conf. I have both TDM40B and X100P cards and am trying to use them together. Please let me know if there is something else I should do. Thnx, Gladys [chan_local.so] => (Local Proxy Channel) == Registered channel type

Morning, I've installed asterisk on FC4 and had a few problems with zaptel stuff. Having installed it on SuSE I was able to check a few things that were different. When installed with the RPMS, the udev stuff gets put into the normal 50-udev file under /etc/udev. On SuSE, it worked when the necessary zaptel section was in a separate file name 55-zaptel.udev (the name is arbitrary,

I have: RedHat 9.0 TDM40B asterisk-0.9.0 compiled from sources zaptel-0.9.1 likewise /etc/zaptel.conf contains fxoks=1-4 loadzone = us defaultzone=us loaded modules zaptel and wcfxs /etc/askterisk/zapata.conf contains [channels] language = en signalling = fxo_ks context = phones channel => 1-4 /etc/askterisk/extensions.conf contains [general]

Hi, I'm no phone guy but I've been having quite a bit of fun messing with Asterisk. I just unwrapped my new Wildcard TDM400P (TDM40B) which is the new 4 port FXS PCI card. It has 4 RJ45 connectors and I'd like to hookup 4 regular phones which are RJ11. If I crip RJ45 connectors to the phone cords do I simple use the center two pins (pins 4 and 5)? Thanks, Randy Smith Tiger

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel