similar to: X100P & T100P knock-off boards

Hi! I think it is a great idea. The DS80C400 needs external memory, and/or flash. It have the Ethernet integrated, but it is really slow (it is 8051 architecture), and yes, I know it can go up ti 75Mhz, but only gives 18MIPS max. I would use ATmega128 from atmel (16MIPS at only 16Mhz), take a look at: http://www.ethernut.de (project using mega128 with Ethernet, includes schematics). It

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Hi I thought this might be of general interest. Recently I purchased an X100P from a Digium reseller in the UK. Very pleased with the card; works perfectly. My friend (known for his deep pockets and short arms) purchased an X100P card from Ebay. He's had no end of problems with line noise, dropped called etc so I thought I would compare the two cards. Plus mine was delivered within two

Hi all. First thing: I want to thank you all for your help over the past month as I've been learning asterisk. This is one of the more helpful lists. Even when I ask questions that have answers in the wiki ( which I missed because I've been over studying ). Second thing is this: My office is scouting out VoIP solutions, and I have suggested an asterisk solution. We will be

I'm attempting to configure a machine with a DevKit Lite (X100P & S100U). After I modprobe wcfxo, the machine goes into some kind of loop after about 10 seconds, where it spits out what appears to be 32-bit addresses, ad infinitum. At this point, the machine becomes completely unresponsive to keyboard input (i.e. Ctrl-C, Ctrl-Alt-Del, even CapsLock and NumLock states [lights] cannot be

Hi, I have two E100P boards connected to my PC. I wish to setup two E1-ISDN-PRI lines, the first SPAN with 15 channels and the second one with 30 channels. When I try to load zaptel modules, I get an error message: "Loading zaptel framework: Loading zaptel hardware modules: wct1xxp wcusb Running ztcfg: ZT_CHANCONFIG failed on channel 63: No such device" Follows my zaptel.conf:

Hi List, a number of our customers are reporting dropped calls. here is the config. 1 T100P T1 Card 1 Asterisk (Mid Nov build) T1 is signalled as a PRI(National) The card will only sync up if we clock, if we line side clock the card goes into yellow alarm and won't sync up. the only errors we see are framing slips. Around 2500 slips over a 18 hour period. (this was reported from

Rich Adamson writes >>GMRS, FRS and MURS radios may not be interconnected with the PSTN (47 > > CFR 95.141). There has been a lot of talk from lobbyists to clarify this > > rule, but as it stands you could conceivably connect a *private* network > > to GMRS or MURS radios (you can't make any plugins or modifications to > > an FRS radio that isn't type

Digium X100P / new cards are is available on ebay for $43. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3073050567&category=3309 <http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3073050567&category=3309 > Hope this helps to who want to play with X100P! Are these being sold by Digium ? I don't know ?? - SamW -------------- next part -------------- An HTML

Anyone know why the knock-off X100p prices have jumped? -Nate

If you have used * to support a pri as pri_net (as opposed to pri_cpe), either to talk to another * system or a PBX of some sort, I would be very interested in hearing about your experiences. Imparticular, I would like to know that it works before I invest in the extra hardware. TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 284-5800 ext 115

I don't know what I am missing in my conf files, but my T1 card grabs all available channels and won't let go of them? Anyone know what the problem is? -- Shawn Parker Network Administrator Cumulus Broadcasting, LLC. Columbia-Jefferson City, Missouri 1.573.449.4141 shawn.parker@cumulus.com

Hi all, I've seen a couple of posts recently from people who are doing something with Asterisk and a T100P and a Nortel PBX. However it's not clear exactly what they are doing. Does anyone know if it's possible to use a T100P or T400P as a DSX-1 interface to connect to a T1/PRI CO module in a Nortel PBX? We have a Nortel Norstar Modular ICS PBX and I'd like to plug its CO

I concur with Jose. The Atmel AVR series packs a lot of bang for the buck. They also come in a 3.3v low power version for use in battery powered systems. Gene -----Original Message----- From: Leo Ann Boon [mailto:leo@innovax.com.sg] Sent: Tuesday, August 19, 2003 7:21 PM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Re: Open source IP phone, maybe? Ubicom's Scenix IP2K.

https://wiki.asterisk.org/wiki/display/AST/STIR+and+SHAKEN The Wiki above is misleading in what Stir-Shaken means and how it works. End users cannot get a certificate, they cannot self-certify their calls. Somebody completely misunderstood the model. I am afraid the moment will come and thousands of Asterisk operators will be unable to terminate calls. To start with, the model is a hierarchical

I have a pri comming into a t100p in my asterisk box. I have a second t100p configured as pri_net connected to a nas server. I can route modem calls to the NAS with no problem, but I am concerned about isdn data connections. Will asterisk route 64k isdn calls between 2 t100p's? Also, should I expect worse modem connections than normal? Chad Sawyer -------------- next part --------------

Group Can I have 2 wildcard T1 cards in the same box? I was thinking the first card would have channels 1-24 and the second card would have 25-48 Does this sound correct?

Im tryingn to run a cd from the windows 3.1 to '95 era. Its a Ford factory service manual disk for pulling up automotive diagnostics/schematics etc. The disk installed without a problem using wine /path/to/cdrom/install.exe . I can also run the locally installed executable file without a problem once again using wine /path/to/local.exe . The problem is that the program requires a callback to

Hi- I have posted a photo of the TE410P Digium card on my site, so that those wishing to purchase a compatible motherboard can see physically what the PCI slot requirement is: http://www.evtmedia.com/TE410P.htm I believe the required slot is a 64-bit, 3.3 Volt PCI, most commonly found on Xeon-based motherboards. A 64-bit slot is longer than the TE410P board requires, but the PCI connector