similar to: FXS Card Recommendation

I think I have a bad FXS module on my TDM400P. Channel map: >> >> Channel 01: FXO Kewlstart (Default) (Slaves: 01) >> Channel 02: FXS Kewlstart (Default) (Slaves: 02) >> >> 2 channels configured. >> ZT_CHANCONFIG failed on channel 1: No such device or address (6) The zaptel loads ok, but the wctdm reports No such device or address and stays loaded. The

Hello, everyone After having spent several time to look for any solution for my problem, I decided to write here. Here is the problem got a Digium X101 FXO card and Digium TDM400P alias freshmaker (1 fxs module on it on first port ) in my asterisk box. The X101 works perfectly. The problem comes from the TDM400, when i plug a tested working phone on it , i get no dialtone; the goal is to

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

I apparently have a dead FXS module. Is there any kind of test I can run on it (on a live system) to determine if its good or bad? The telephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO

I acquired a board identified as a Dialogic/4 for which I've not been able to locate any technical details. Can anyone identify this board or point me to some technical data? Thanks. -- Regards, Scott Dudley

Is there any product that's a single port mini-PCI FXS card? I'm aware of the Openvox A400M <http://www.openvox.com.cn/products.php?genre_id=39>, but I really only wanted one port. How about a single or dual port PCI or PCI express FXS card? Basically I wanted to build a small linux router with one or two phone ports. Alternatively, is there already a router or single board

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi; I'm trying to connect a TDM400P with an FXS module to a Valcom V-9940 Paging adaptor. This port on the TDM400P was connected to a 2500 Set and was working I just re-connected it to the Valcom (which is known to work on a Telco POTS line) and its not picking up. The Valcom docs say it need a minimum of 75 Volts at 20-30 Hz to recognize a call... So the question is what ring voltage

hi all, i need an asterisk board that can support up to 30 FXS ports. i found the following on digium: TDM400P. It only has 4 port, does it mean that i have to buy 8 of those to have my 30 FXS line? Or is there any channel bank solution that digium or other providers can provide us with in order to do that. Experienced asterisk user, how do you manage to make PBXs for 30 to 100 regular phones?

Hi all, I have a brand new TDMxxx card with 3 FXO modules and one FXS. It has replaced my old 3 X100P cards. The FXO part work as before, after some adjustments in the rxgain/txgain part. The problem I have is with the FXS module. I can place calls to SIP/IAX or PSTN destinations without any problems, but the sound received by the other part is much to strong and a little bit distorted. I have

we have got asterisk 1.0 (over 1 yrs old) version and very old zaptel version. That code is working only with 8 or less ports (accumulative) on digium fxs/fxo cards (2 cards with 4 ports each). the questoin is, what if we want 12 ports?..well, really, i don't understand the limitations? is it simply zaptel driver code fix? or kernel fix? or technology limitation? donno any tips would

Hello everyone, I'm trying to set up a Asterisk server. I have two cards - one is an BeroNet BN2S0 with two ISDN lines (4 channels): http://www.adcomtec.com/webstore/beronet_bn2s0.php?cat=90 and a Rhino R8FXX with one FXO module and two FXS: http://www.voipsupply.com/product_info.php?products_id=2940 I would like to set up an Asterisk server with 8 phones, which will share the phone

We have a recently deployed server with a new TDM2400 card that will not put dialtone or audio on FXS ports after the physical server restarts (though they will ring if called, there's just no audio on the line if the phone at the other end picks up). The symptom can be resolved by stopping Asterisk, restarting DAHDI, and then restarting Asterisk. So far, this has happened on both times the

I have an intermittent problem with the one FXS line that I have. On most calls, the first ~5 seconds of the call has a loud buzzing noise on the line. After 5 seconds or so, it fades off to nothing, and the sound quality is great. Searching for "buzzing" on the list doesn't give a whole lot to work with. The buzzing happens on calls that are routed over both my FXO line and

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

I just received a Wildcard TDM400P by FedEx yesterday. I noticed that the FXO/FXS modules use connectors similar to Ethernet. Now, i want to connect the TDM400P to the PSTN connector in the wall, and also to a regular analog phone. Both the PSTN conn and the phone use smaller connectors, typical for analog phones. I searched the "official" docs and the Wiki, there's good

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Hi, I have a client that have currently 400 analog phones (all wired w/ Cat3). I need multi-ports FXS interfaces but I only find 24 ports FXS (like Mediatrix 1124) but it's a little bit expensive to get 15-16 box (~408 FXS ports). Someone have suggestion to link all theses phones to "channel bank" ? What equipment to use ? Currently all 400 lines are terminated in M-66 blocks and

Hi All, What do you recommend? I was looking at: http://www.voipon.co.uk/sangoma-a200-fxo-fxs-analogue-card-pci-express-p-393.html But it will be 3 PCI slots. Thanks, Gavin.

In my attempt to setup a single FXS line I have been following the instructions for "Telephony Card Drivers" on the asteriskdocs.org site. I have managed to checkout, make and install the zaptel code and can load the zaptel module but when I attempt to load the wcfxs module it tells me: ZT_CHANCONFIG failed on channel 1: No such device or address (6) FATAL: Error running install