similar to: Secondary gatekeeper support by asterisk h323 drivers

Hi, I'm trying to interconnect sip and h323 endpoints using asterisk and asterisk crashes with segmentation fault whenever h323 connection needs to be established. It registers with gatekeeper ok though. Here are the symptoms. If the call initiated by SIP device, asterisk replies to it "Trying" and then silently crashes (it launched as asterisk -vvvvcd). In debug log I can see the

Hi all, i have tried to connect to a clarent gatekeeper. I have used both of h323 drivers chan_h323.so and chan_oh323.so. But no one can register to this gatekeeper. Our ip is activated on this gatekeeper. Maybe, i do wrong anything.... I have only set the "gatekeeper" option in the h323.conf or oh323.conf to the ip address from the gatekeeper. gatekeeper=x.x.x.x But no one of the

Hi, Has anybody managed to get callerid properly set on a call from local to asterisk SIP endpoint through h323-pstn gateway to a regular phone. I'm using ata186 as SIP endpoint. It has 12125551234 assigned to it. When I place a call to pstn I'm not receiving 12125551234 as the clid, but a number assigned to PRI channel by phone company. It worked with chan_oh323, but there were other

Hi, Someone released a succefull interconnection in H323 with WTL equipement ? I'm trying to do that with an IPNx. But get dead air. With chan_oh323 it's fine, all works. With chan_h323 => dead air. The configuration is GW to GW. This is my configuration from h323.conf: [general] port=1720 bindaddr=my.ipaddr dtmfmode=rfc2833

Dear All, I have installed GNU gatekeeper in my machine. I tested the calls using gatekeeper successfully. Now I have tried to Disable the gatekeeper in oh323.conf file gatekeeper=DISABLE Now I have tried to call, but the connection is not established. I have got following warning message in console. " WARNING[8446]: chan_oh323.c:3555

Hello All, I am trying to setup a SIP to H323 system using SER, Asterisk And GnuGK. Following is the configuration: CISCO ATA (NAT) -> SER -> ASTERISK -> GNUGK My Cisco ATA is registered with SER and When I dial a number, SER forwards the call to Asterisk, and Asterisk forwards the call to the GateKeper. This is ok, call reaches the gatekeeper, however the gatekeeper drops the call

Hi All. I'm using RedHat 9 I configured the chan_h323 and asterisk from CVS. This is the scenario SJ_lab_phone(sip) ---------------> Asterisk -------------> H323 GK --------------> PSTN I have tried all codec's and always the same result, the called phone will ring without dropping for how ever I allow it to but as soon as it is answered it immediately gets disconnected.

I have built Asterisk on SuSe Linux 7.3 on an Ultra 2 Sparc WorkStation. I am listing the modification I had to do for the benefit of anybody else who wants to use Asterisk This workstation is equipped with one 400 MHz RISC UltraSparc II CPU, 256 MB RAM, Two 9 GB 10,000 RPM UltraSCSI Disks. I have a gatekeeper running on this machine, I had to do the following modification to build * on Sparc:

Is there anyone who is currently using Asterisk as a production H323 gateway? And using which combination of asterisk and H323 (chan_h323, chan_oh323?) The main issue is interoperability with other H323 parties (Cisco AS53xx, Nextone, etc). Searching the mailing list it seems that both h323 and oh323 are not so stable, is it only an impression or using h323 is really not so advisable?

Hi, I want to configure * to use a gatekeeper for routing calls to H.323 endpoints. I imagine it will work like that: * (chan_h323) will query the gatekeeper where to terminate the dialed number and the gatekeeper will return the information for the h.323 gateway. after that chan_h323 will try to make the call to the gateway it has received from the gatekeeper. so instead of duplicating a

I have tried everything. to register with this gatekeeper to make and receive calls These are the details I received from the voip provider: protocol H.323 Gatekeeper Address - AVS@210.21.118.XXX Port - 1719 RAS - 53 Q931 - 80 h245 - 1722 RTP - 1722 Username - H323 I have 2 phone number/accounts with this gatekeeper that I need to register to. ID - HMA0200.10szxn-xxxx e.164 - 22xx2912

Dear friends, I have compiled and installed h.323 in my asterisk. And I have a service from a H.323 VoIP provider who give me user, password and gatekeeper IP address. All configured. But when I start my asterisk i receive the following error and h.323 calls can not be making and/or receiving. [chan_h323.so]=> (The NuFone Network's Open H.323 Channel Driver) == Parsing

I'm trying to configure Chan_H323 to register with GnuGK... without success... i've failed finding sample configurations. I'd greatly appreciate anyone who can provide sample config of H323.conf and gnugk.ini I am tyring to configure Asterisk as a neighbor in GnuGK. I'm always getting this error on Asterisk. ERROR[16384]: chan_h323.c:1987 load_module: Gatekeeper registration

Hi Users, Administrators and Pavel Jezek, You prefer chan_h323 from asterisk tree and it's of course that use channels by tree is very good. But in 1.2.x, the chan_h323 is very simple and the chan_oh323 is so bad. And I work with chan_ooh323, that it's too from Digium and work good! And I am Studing one possible change to Asterisk 1.4.x , but in 1.4.x the oh323 channel don't have more,

Hi all, I try to ask helps again about chan_h323 extensions. I define this in h323.conf: [general] port = 1720 bindaddr = 0.0.0.0 allow=gsm allow=ulaw gatekeeper = DISABLE context=default [gm1] type=friend host=192.168.1.20 context=default [gm2] type=friend host=192.168.1.25 context=default and I have in extensions.conf : [demo]

Actually I am facing a problem with H.323 (the standard and the ooh323) with Asterisk vesion 1.4.25 and I discover the following: 1) Using the standard h323 that come with Asterisk: The chan_h323.so it is not existed in the /usr/lib/asterisk/modules after doing the compilation and installation for (pwlib, openh323, /chanels/h323, asterisk), although make menuselect was done and the h323 channel

If anyone in the list has a working version of the chan_oh323.so file for Fedora Core 2 and Redhat, can he email the same to the list as attachment. This will reduce the pain for many of the users who are trying to compile the same from the libraries, which never seemed to work. Seshu Kanuri -----Original Message----- From: asterisk-users-bounces@lists.digium.com

A very strange problem.. * dies with seg fault when calling from SIP to h323 WARNING[589848]: File chan_oh323.c, Line 2429 (alerted_h323_connection): Call with reference 183 in unexpected state (4). -- Called 113506 -- H323:183 answered SIP/alex-1e48 Segmentation fault I'm using Mandrake 9.1 , lastest * ( 3 day old from cvs) , and oh323 last version.. here are my configs:

Hi there ! I searched the whole web to find some helping information about H323 Control Protocol, but there is no way to find that information. We compiled and installed asterisk_0.9.0 + pwlib 1.5.2 + openh323_1.12.2 + 'asterisk-oh323_1.5 channel driver + wrapper' and configured the dialplan for using our H323 Endpoints which are ip200 Innovaphones. Besides, we also use Gnomemeeting but

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi. Using inAccess Networks chan_oh323, I'm experiencing some clicks or pops, how can I fix that? - -- Regards, Tais M. Hansen ComX Networks Tel: +45-70257474 Fax: +45-70257374 -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.2 (GNU/Linux) iD8DBQE/QMfF2TEAILET3McRAu9zAJwNWtv+QSpka0NGaVk9E/IDHyalhwCgkQME Gynfp5zF0SWZUQEjelp7sBI= =CSqT