similar to: T100P/ TSU 600 installation problem

Hello, Did anybody successfully tried upgrade Adtran TSU 600 to firmware which is working properly with T100P and asterisk ? B.

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

I am working with the telantek.adsi file, and I was wondering how I would create a softkey for Transfer. I tried making a key definition and using SENDDTMF "#", but that didn't work. Is there another way I could do this? Also, does anybody have any ADSI scripts for use with Asterisk that they would like to share? Thank you for your time. __________________________________ Do you

I recently set up Asterisk with an Adtran TA750. All is well except the phones do not show the MWI. I have configured zapata.conf properly, as all phones will receive a stutter dial tone if there is a message waiting in it's assigned mailbox. Does anybody know how I might fix this problem? Thank you for your time __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free,

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31

I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type

i wrote previous about a setup i thought might work with asterisk and the tsu-600. no one replied, so i thought i would ask if anyone is using a tsu-600 with asterisk and if so how do you have it setup ??

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Hi, I have a 1 port T1 card in an asus p4p800-vm board with a 2.0g Celeron, and 512m of 266mhz ram (256 on each channel). This board has video, Ethernet, and serial ata all on-board, I got it because of that, there wouldn't be anything else on the pci bus that would mess with the zaptel card(s). So, here's my problem. I'm running redhat 9 with kernel 2.4.20-20.9. I can load the

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

People on the list tend to think you can't make many cards work on a regular desktop. If you're willing to wait a couple of week I might have an answer for you. _____ From: Robert Augustyn [mailto:augustynr@yahoo.com] Sent: Saturday, December 11, 2004 7:13 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] Will Adtran TSU 600 work with *?

It is possible to connect ADTRAN TSU 600 VP24 FXO 24 Port Channel Bank to Asterisk ? Somebody offered me that hardware, but I do not know if thats good hardware for Asterisk. rgs, Bartosz -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030820/4a9e4608/attachment.htm

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

Even though they make the cards and advertise that they support data modes, digium won't support data mode on the $500 card they sold to me, so I must turn to the list. Has anyone configured a T100P to use a T1 strictly as bandwidth? Is there a HOWTO somewhere? Wiki has nothing I could find. I've got plently of public IPs I can assign to it but don't know how. Thanks, Matthew -----

I keep getting segmentation faults when I do a reload. Here are the core file outputs from gdb: (I have three of them and they produce the same output) (gdb) core core.6044 Core was generated by `asterisk'. Program terminated with signal 11, Segmentation fault. #0 0x401519fc in ?? () I have no idea what that means, but if somebody could point me in the right direction, that would be

I just received an unlocked ADSI phone and I am playing with the ADSI script. I was wondering how I can include Voicemail functions (Check new messages, Delete message) into the soft buttons. I checked in app_voicemail.c and it looks like these functions have already been programmed. Is there a voicemail.adsi script somewhere? If not, then how do I get the functions I want onto my phone? Thank

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to