similar to: Re: ATAs

John Todd wrote.... > Cisco has an 802.11 phone called the 7920, which is apparently > shipping now. It is very expensive (>$550 USD) and only runs SCCP at > the moment, which is Cisco's proprietary VoIP protocol. However, if > it falls in line with some of Cisco's other high-end VoIP equipment, > that means it should have a trailing-edge SIP image running by

> Message: 5 > Date: Fri, 12 Sep 2003 13:24:13 -0400 (EDT) > From: "David C. Troy" <dave@toad.net> > To: asterisk-users@lists.digium.com > Subject: [Asterisk-Users] 7206 as SIP->PSTN Gateway? > All, > > I know you can use, say, a 2620 w/2 port FXO card as > a SIP gateway. Clearly you can use the 5300, 5800, and > MGX8850 too. > >

During debugging of H323 trunk side (using Jeremy Macnamara's H323 driver in ~/channels/h323) a couple of things come don't quite work as advertised... 1/ the following line in extensions.conf explicitly sets the outgoing caller ID (required in my case for downstream GK processing..) exten => _1NX.,1,SetCallerID,6400047602100 exten => _1NX.,2,Dial,H323/${EXTEN:1} what

From the thread..... > Subject: Re: [Asterisk-Users] IAX <> IAX trunking... DP cache? > Date: 20 Aug 2003 11:29:59 -0600 > From: Steve Meyers <steve-asterisk@spamwiz.com> > >>Brian West wrote: >> >>>I would use the latest CVS for one. And try again. >> >>Unfortunately, I've tried numerous times to get a current CVS trunk

I have successfully built and made asterisk talk SIP extension to SIP extension, read all the docs, and about 1000 emails from the archive. The trunk side of Asterisk, from the docs perspective, is a smidgin TDM-centric, Analogue, T1, zaptel.conf etc..... Asterisk cares not about the externally presented digits as the telco KNOWS which time-slot or analogue line the call came from I live in an

Hello Sa?o! I found you here: http://mail.opensolaris.org/pipermail/zfs-discuss/2012-May/051546.html "How about reflashing LSI firmware to the card? I read on Dell''s spec sheets that the card runs an LSISAS2008 chip, so chances are that standard LSI firmware will work on it. I can send you all the required bits to do the reflash, if you like." I got Dell Perc H310 controller

> On Nov 11, 2020, at 5:38 PM, Warren Young <warren at etr-usa.com> wrote: > > On Nov 11, 2020, at 2:01 PM, hw <hw at gc-24.de> wrote: >> >> I have yet to see software RAID that doesn't kill the performance. > > When was the last time you tried it? > > Why would you expect that a modern 8-core Intel CPU would impede I/O in any measureable way as

Howdy, I know that syslinux doesn't currently support this, but does anyone here know how I might go about getting some sort of boot process together that would have a single firmware image as opposed to seperate files for initrd, kernel, and root fs? Thanks.

Hello list- I'm having an extremely odd issue with an installation of mine. The system is running * 1.2.12.1 and currently handles around 100 handsets. With the exception of a few Grandstream DTA's, all devices are Polycom 320, 430, or 601's. After a recent power outage, I'm having an extremely odd issue with one of the handsets. One of the Polycom 601 units simply reboots every

Hi all, I have a Polycom Soundpoint IP 600 that looks like it is fried. It either has a bad or corrupt bootrom (I'm guessing). It never gets to the prompt that asks if I want to enter the setup configuration or continue booting. When plugged into power, it turns on, shows the Polycom logo for 3 seconds and then pretty much goes dead with two red lights on. The one in the top right corner

Hey, all. Got an SNOM 820 in the other day to kick the tires. As with many phones, provisioning it was a bit of a PITA. The biggest problem, as far as I could tell, was that their firmware just doesn't seem that stable, and is sometimes hard to get to. - I managed to corrupt the firmware twice; fortunately, instead of bricking the phone, there's a fairly easy-to-use "rescue

Hi, I have been trying to boot a PC based terminal using your PXELINUX project and I am having a problem. The Terminal (a Netier NetXpress XL2000) has a m-systems Disk-On-Chip 2000 flash memory module which is normally used to boot a cut-down version of WinNT. I work in a repair department where we often have to open up these terminals and temporarily install a hard-drive to reflash the

Hi: I use this driver to set up my Fedora Core 1 as a PXE server. After I successfully boot up from network in my laptop, it erases my Intel PXE boot manager from my laptop's BIOS. The BIOS of my laptop has an option to choose form "boot from ethernet", but it is gone after I use this driver. Now I have to reflash my laptop's BIOS and Intel PXE boot manager ROM to make it come

HI all, I wonder how rsync works when files-to-be-updated are in flash (e.g. on IPAQ) Ideally rsync should write to the flash as little as possible (because of max reflash count) SO ideally the following should happen If file needs to be updated, the new file is created. Then the old file is deleted the new file is renamed to the old file (making sure that the file does not get copied over)

Hi, folks, Got an older Dell R410, with an LSI 1068E PCI-Express Fusion-MPT SAS (rev 08). It *appears* that a) trying MegaRaid, and b) from what I'm googling, that what I need are mptfusion-related packages. Unfortunately, yum shows me nothing available in base, epel, or rpmfusion. Am I looking for the wrong thing, or does anyone have a source (no, I haven't looked at LSI, sorry

Hello, is pxelinux intended to work with Token Ring Cards ? cause i have a nice IBM Token Ring PCI Card (olympic) and sadly pxelinux hangs when trying to get the configfiles via tftp... last message: "Trying to load: pxelinux.cfg/<hexip>" but no tftp packet was sent (serverlog empty, ethereal shows no packet either) i tried versions 1.67, 1.75, 2.00-pre4... using ethernet,

Hi, Does anyone know how to make this thing (7940) work with asterisk (chan_sccp module) ? I've set the configuration according to the wiki and now the phone just keep asking for CTLSEP<xxx>.tlv from my tftp server. In the cisco's web interface, I found this in the device logs : 0x8106, 0x0, 0x12300800 0x8106, 0x0, 0x12300800 0x8106, 0x0, 0x12300800 0x8106, 0x0, 0x12300800 ...

I'm having lots of problems with sipura spa1001's and spa2002's. Asterisk claims they are busy when they aren't. Other times, it claims to be ringing them, but they aren't really ringing. I have done the following to try to resolve the problem: 1) I upgraded all my spa1001's and 2002's to their latest firmware (3.1.5). This lessened, but did not resolve

Hi, I just got and setup a new ip500 yesterday and it worked for about 15 minutes. Then it froze during a reboot.Now, when power cycled, the logo comes on for 3 seconds and then the screen is blank and nothing further happens. 468* factory reset doesn't work. I am about to send the phone back, but wonderd if anyone had a suggestion first.

On Fri, Sep 03, 2004 at 03:01:01PM -0500, Anshu Dasgupta wrote: > ><snip> > >for (BasicBlock::iterator I = Dest->begin(); PHINode *PN = > >dyn_cast<PHINode>(I); ++I) > > visitPHINode(*PN); > ><snip> > > > >build_vc71\lib\Transforms\Scalar\SCCP.cpp(202) : error C2275: > >'llvm::PHINode' : illegal use of this type as