similar to: Best E1 channel bank?

I'm first to buy 5 pack. Even for > $30.

Hi, one short question: Is it possible for the zaptel driver to deal with multiple phone numbers on one single E1 PRI line? I could make my carrier route +49 xxx aaaaa-zzz and +49 xxx bbbbb-zzz and others down one single PRI trunk to our asterisk box terminating in a Digium TE410P. Does the driver handle this and can I put calls coming in all on the same physical interface put into

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

I hate to bring this thread back to life, but... > it may be possible to get it supported, do you think the price >point is remotely competitive with Digium hardware? Also as I am not >about to divulge my information to them to look in the downloads >section, what is the licensing of their SDK? What is the licensing of >the driver? > >Steven >On Tue, 2002-11-26 at 14:52,

Anyone ever experience noise instead of a dial tone. We are using a Digium TE410P and 2 units of Rhino FXO & FXS Channel Bank. Everything works well when they are freshly turned on or rebooted, but after a while there's only noise can be heard instead of dial tone. Does this have anything to do with the timing configuration? Where is this time is generated from, is it from the TE410P card?

Must accepts wire transfers and ships to Sofia. Thanks

hi guys, do you have any suggestions on how to connect 2 TE410P via E1? (for simulation and testing purposes) asterisk1 --> TE410P ----> ? ---------> ? ---->TE410P -->asterisk2 -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030907/698cd499/attachment.htm

I just need to buy 5-6 ADSI Phones. I wondering which of these models to choose - aastra 390 - I don't know is this an ADSI phone at all. Is there versions with and without ADSI - aastra 350 - I'm sure that it have ADSI. If there is some other good working model, it will be great, if someone points me. Thanks

hi, we are currently planning are large site which will migrate from an old siemens hicom pbx to asterisk. it will be a slow migration, the asterisk server will be inserted between the telco E1 and the hicom. new phones will be sip ones. the customer has several fax machines and analog phones (some of them have to be explosion-proof). around 50 analog ports in total are needed. as we are in

Hello all, please, can anyone advertise me some channel banks, which can operate with E1 (30 FXS)? Rack-mountable option is welcome. I've tried to google, but I've not found nothing appropriate. More than one E1 link is welcome too. Everyone channel banks, which I've found, was between T1 and FXS(O), but I have Digium E1 card and I want use for one line 30 channels and not only 24.

hi guys, i'm in need of several 24port or higher fxs device which supports sip, aside from mediatrix and audiocodes (cisco's vg248 doesn't support sip), do you have any idea who else manufactures such device? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030801/67eb12dd/attachment.htm

I'm looking to install a system with 80 FXS analog phones. At this time the only cost effective solution is using a 4 port T1 card and addit 600 channel bank. Has anyone tried this solution? any good documents beside http://www.voip-info.org/wiki/index.php?page=Asterisk+hardware+channel+bank+check as far as i know, addit 600 T1 interface is not PRI (please correct me if i'm wrong) its CAS

Hello Everyone, What kind of hardware setup would I need to do if I want a T1 connection to PSTN and have 48 users in office with analog phones. Will something work if I have a T410P card in asterisk and have one T1 going to PSTN and other two to a channel bank. I would then connect the 48 phones (FXS) to the channel bank! Thanks. Deepak

Hello All, I'm looking to get some feedback on which solution of providing FXS is going to have the best results with faxing. I'm only looking to see what method is going to provide the best digitization into Asterisk, not for transmission from Asterisk to else where. Any recommendations of specific channel banks are welcome. I will need to provide approximatly 216 FXS Ports and need

Hi, I wish to know if GNUGk can work with * running as a gateway with the Digium FXO card. Kindly share your experiences in case there are some issues which one must know before going in for such a setup. Also, I've been reading about the DialTone detection capability by the hardware in different countries. What are the issues with it? Thanks & Regards, Deepak ----- Original Message

I just got my Access Bank 2 (of course i'm happy now:)). Just need the wiring scheme Thanks

Hi! Is there anyone that are using a E1-channelbank and have any tips about some type? Im looking at the TE410P and use one port for a PRI (Euro-ISDN, I think we're using some slightly modified version here in Sweden, but I'll check that tomorrow) and connect one port to a channelbank for 30 analogue telephones. It would also be great to get callerid on the analogue phones, so it would

Greetings list, I've been asked to provide a system for 200 extensions, most of which will be existing analogue POTS handsets, not IP handsets. I've not really had any experience with large channel banks in the past (since most of our deployments are strictly IP-only to the desk), so I'm at a loss as to which ones are worth looking at. If anyone's had experience using channel

Hi List, After reading a bunch of the docs, list post archives, it still seems that a clear definition of how to clock the T100P card is muddy. zttool says that the link is "INTERNALLY CLOCKED", does this mean the T100P is providing clock, or does this mean the T100P is getting clock from the T1 line side (ergo getting clock from the Telco) ?? If you have sync = 0 then zttool

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: zapata.conf Type: application/octet-stream Size: 590 bytes Desc: zapata.conf Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20040811/dfc853bc/zapata.obj -------------- next part -------------- A non-text attachment was scrubbed... Name: zaptel.conf