similar to: Can't install CentOS4

Ok, here's what iam trying on,, a compaq proliant 8500 server with 8 xeon 550mhz processors, 6 gig ram,, i just installed centos 4.1 on a proliant 3000 dual 550's and 2 gig ram and went smooth as silk, just got the 8500 and it seems to be in good order, but when i tried (twice) to install centos 4.1 it stalls shortly after a screen of stuff installing and the last two items are something

Could the problem be that the e100 can do IP receive checksumming on the board, but the eepro driver doesn't enable it. When the board is doing checksum offload, then the csum field isn't set. Please try disabling receive checksumming on the e100 driver modprobe e100 XsumRX=0 If this is the problem, it exists both 2.4 and 2.6. On Wed, 27 Aug 2003 18:24:57 +0200 Hannes Schulz

I was doing an Internet facing server reload for a client today and he mentioned that there is a minimal install selection somewhere and that I should take a disk 1 of centos 4.4 and it would be under custom Is this the case? How? I couldn't find it, nor could he after the fact. If it exists, where is it, or how do I get to it for future reference please? I usually use a centos server cd

Hi, I have a machine running under CentOS 3.4 which I want to upgrade to CentOS 4. I booted using the CentOS 4 CD1 using "linux upgradeany". Problem is that loading sata_via never terminates. Ismod shows the sata_via module in state "Loading" while all others are in state "Live". The dmesg output shows that the module gets loaded, sees two disks, then prints info

Hello lists, I,ve compaq ML350 with 2 Xeon 2.4 GHZ and FreeBSD 5.0 RELEASE installed and working very fine about 4 mounts. The machine running GENERIC kernel samba and firebird database server with no problems until at begining of this week, in morning machine freezes with no responce iven in conconsole, no responce from network (pinging) no responce on console (key pressing) the only way to get

hi there. anyone have any tips on params to pass to the kernel etc in order to install Centos4 or Centos5 32bit or 64 bit installed on this unit i can get it close to install, yet no cigar. it is a tyan MB and ill try to get more info if needed... for this case, please assume for now that the hardware itself is not "bad" thanks in advance... - rh Rackable Systems Dual Opteron 2.0

I'm having some trouble here - need some help! I've just bought a TE405p (32-bit 5V), but cannot get it working in a dell 6450. The dell has (from tech specs) "three peer PCI buses: two 64-bit buses and one 32-bit bus Expansion slots seven hot-pluggable PCI slots (two 64-bit/66 MHz, four 64-bit/33 MHz, and one 32-bit/33 MHz)" I cannot get the card working in any of the slots.

Greetings, I have several Tyan S2518UGN (Thunder LE-T) server boards that I've been running for a few yrs. I've always used the SCSI on them, so never really used the ATA ports. I once experimented dual-booting NT2003 & FBSD on one of the ATA ports about a year ago. But ran into the problem I'm running into now. Back then I just blamed it on the drive (even tho it was brand new,

I want to buy a Lenovo U160 laptop, Core-i7, 16gb DDR3, 500gb HD What I am trying to accomplish is to use a Hypervisor that boots up and then have a Windows, Linus and OS X VM that also gets started up and I can interact between them while still on the same laptop. I have a fair number of reasons for wanting this between software development for all of these platforms to pen-testing, etc. Can

Hi all, is there a known issue with health monitoring on supermicro SuperServer 6010H? (Im primarily interested in temeperature monitoring) I have tried both mbmon and lmmon with the following results: stats# mbmon -d SMBus[ServerWorks(ServerSet Chipset)] found, but No HWM available on it!! No Hardware Monitor found!! InitMBInfo: Unknown error: 0 stats# lmmon IOCTL: Operation not supported by

I tried installing with several options (noacpi noapm; noprobe; noprobe skipddc noacpi noapm nodma). Always I get the same error. BUT this is not in fac a CentOS problem at all, because I get the same error always when I boot from hd (Fedora Core), IF there is a CD in the CD-ROM drive. (I tried with CentOS 1/4, CentOS 2/4 and a HP printer software CD.) It must be something with the CD drive!

From: Tony Wicks <tonyw at tonyw.com> > I run Centos on Compaq dl380g1/2/3's and Dell servers. While the > Compaqs are strong hardware they are old and frankly the performance > compared to modern (cheap or otherwise) hardware is not really that > impressive. A dual 1 gig P3 dl380 and ultra 3 scsi drives get significantly > out performed by a generic celeron with software

Hi, I received a bug report against BerkeleyDB 4 that may not be BerkeleyDB related, but a problem with FreeBSD or specific hardware in general. Jie Song (CC'd) reported that writing files with BerkeleyDB (no threading or something) on his ServerWorks machine causes data corruption (detected by BerkeleyDB 4.0 library functions) when the file sizes grow beyond 350 MB. For details, see PR

Has anyone had successfully installed more then two digium wildcards in the same machine? I'm going for four. thanks Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd. Office: +972-3-9230686 ext. 179 Fax: +972-3-9216642 Mobile: +972-54-8000200

Hi, I would like to share my experience with total server lock-up during CentOS5.1 installation using vnc installation method. My setup was as follows +--------------------------------------+ | my_PC, CentOS4.6 | | X, KDE, vncviewer | | 100Mbit/s eth0 | | Intel Corporation 82801BA/BAM/CA/CAM | +------eth0----------------------------+

Hi, I am running a Xeon with hyperthreading support. Until last week's HTT modifications, according to ps(1) and top(1) both logicals CPUs were in use. (Processes in CPU0 and CPU1 state; "C" column showing "0" or "1".) This has changed with a recent -STABLE kernel which includes last week's changes to HTT (removing "options HTT"). I am only seeing

hi guys i just partially upgrade centos 3.4 to centos 4(using apt-get) and im having a problem removing kdb 1.08-10.2, kbd 1.12-2 is already installed and im trying to remove kdb 1.08 through apt-get and rpm -e here's what happened when i use apt-get: # apt-get remove kbd#1.08-10.2 Reading Package Lists... Done Building Dependency Tree... Done The following packages will be REMOVED:

Hello everybody, After going through multiple posts on Internet and trying different things I can't seems get zaptel wcfxo loaded on the server correctly. I run dual P3 500 Mhz box. After reading README.udev I put a file 60-zaptel.rules /etc/udev/rules.d # Section for zaptel device KERNEL="zapctl", NAME="zap/ctl" KERNEL="zaptimer",

I have FC 3 running on my "play/test" box. Is CentOS (RHEL) a level above? Can I do an Upgrade or should I do an Install? Todd -- -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.centos.org/pipermail/centos/attachments/20050730/05888be3/attachment-0001.html> -------------- next part -------------- A non-text attachment was

We have 30 or so boxes that are currently running either redhat as3 or as4 and would like to migrate them to Centos 4.2. We have a local centos 4.2 repository using yam. I have in the past updated es3 to as3 by removing the redhat-release rpm and installing the other redhat rpm. I realize there are virtually no differences in es and as3, except for access to additional packages. In any